background image

Model 4RJ45

5

Teel Operating Instructions and Parts Manual

E

N
G

L

I

S

H

Symptom

Possible Cause(s)

Corrective Action

ENGINE

Not enough 

Speed too low

Refer to engine manufacturer’s manual

water delivered

Not enough 

Speed too low

Refer to engine manufacturer’s manual

pressure

Engine heats  

1. Rotating and/or reciprocating parts drag

1. Refer to engine manufacturer’s manual

excessively

2. Speed too high

2. Maximum engine speed not to exceed engine

manufacturer’s recommendation

Abnormal noise   

Loose or broken parts

Refer to engine manufacturer’s manual

and/or vibration

Pump works for a   

Loose or broken parts

Refer to engine manufacturer’s manual

while, then stops 

PUMP

No water delivered 

1. Pump not primed

1. Reprime pump, inspect suction system for air leaks,

and or clack assembly 

2. Pump takes too long to prime

2. Check for air leaks or defective check valve

3. Flow through the pump is completely 

3. Locate and remove obstruction. Attach strainer

or partially blocked

Not enough  

1. Flow through the pump is completely 

1. Locate and remove obstruction. Attach strainer

water delivered

or partially blocked

2. Internal leakage

2. Check clearances between face of vanes and case.

Clearance should not exceed 1/32”

Not enough   

1. Flow through the pump is completely 

1. Locate and remove obstruction. Attach strainer

pressure

or partially blocked

2. Internal leakage

2. Check clearances between face of vanes and case. 

Clearance should not exceed 1/32”

Engine heats    

1. Internal leakage

1. Check clearances between face of vanes and case.

excessively

Clearance should not exceed 1/32” 

2. Rotating parts drag

2. Inspect and repair

3. Loose or broken parts

3. Inspect and repair

Abnormal noise     

1. Not primed

1. Reprime, inspect suction system and/or clack   

and/or vibration

assembly for air leaks

2. Flow through pump completely or 

2. Locate and remove obstruction. Attach strainer

partially blocked

3. Loose or broken parts

3. Inspect and repair

Pump works for a     

1. Flow through pump completely or 

1. Locate and remove obstruction. Attach strainer

while then stops

partially blocked

2. Loose or broken parts

2. Inspect and repair

Troubleshooting Chart

®

Содержание 4RJ45









Отзывы: