teel 4P035A Скачать руководство пользователя страница 2

General Safety Information

READ AND FOLLOW 
SAFETY INSTRUCTIONS!

This is the safety alert symbol.

When you see this symbol on your

pump or in this manual, look for one of
the following signal words and be alert to
the potential for personal injury:

Warns about

hazards  

that will cause serious personal injury,
death, or major property damage if
ignored.

Warns about
hazards that can

cause serious personal injury, death, or
major property damage if ignored.

Warns about
hazards that will or

can cause minor personal injury or
property damage if ignored.

NOTE:

Indicates special instructions

which are important but not related to
hazards.

Carefully read and follow all safety
instructions in this manual and on
pump.

Keep safety labels in good condition. 
Replace missing or damaged safety
labels.

Electrical Safety

Capacitor voltage
may be hazardous.

To discharge motor capacitor, hold
insulated handle screwdriver BY THE
HANDLE and short capacitor terminals
together. Do not touch metal screwdriver
blade or capacitor terminals. If in doubt,
consult a qualified electrician. 

Wire motor for correct voltage. See

“Electrical” section of this manual

and motor nameplate.

Ground motor before connecting to

power supply.

Meet United States National Electri-

cal Code, Canadian Electrical Code,

and local codes for all wiring.

Follow wiring instructions in this

manual when connecting motor to

power lines.

Do not touch an
operating motor.

Modern motors are designed to operate
at high temperatures. To avoid burns
when servicing pump, allow it to cool for
20 minutes after shut-down before
handling.

Do not allow pump or any system com-
ponent to freeze. To do so will void
warranty.

Pump water only with this pump.

Periodically inspect pump and system
components.

Wear safety glasses at all times when
working on pumps.

Keep work area clean, uncluttered, and
properly lighted; store properly all
unused tools and equipment.

Keep visitors at a safe distance from the
work areas.

Pump body may
explode if used as a

booster pump unless relief valve capable
of passing full pump flow at 75 psi is
installed.

2

Teel Operating Instructions and Parts Manual

4RJ47, 4RJ48, 4RJ49, 4RJ50, 4P035A and 4P036A 

Teel Heavy Duty Cast Iron
Convertible Jet Pumps

®

E

N
G

L

I

S

H

Hazardous pressure! 
Install pressure relief 
valve in discharge pipe.

Release all pressure on 
system before working on 
any component.

WARNING

Hazardous voltage. 
Can shock, burn, or
cause death.

Ground pump before 
connecting to power 
supply. Disconnect power
before working on pump,
motor, or tank.

WARNING

Содержание 4P035A























Отзывы: