Tecumseh 695244a страница 38 Скачать руководство пользователя

Страница: 38 / 94

CHAPTER 6 ELECTRICAL SYSTEMS

END CAP

BRUSH SPRINGS

BRUSH CARD

HOUSING

ENGAGING NUT

GEAR

OPERATION

STARTING CIRCUIT AND ELECTRIC STARTERS

GENERAL INFORMATION

The electrical system consists of three main elements: a battery, a starting circuit, and a charging circuit. The

battery is part of both the starting and charging circuit. The battery should be checked before going into any

extensive starter or charging system checks. If a battery has a shorted cell, overcharging can result, and the

regulator or rectifier may appear to be at fault. If a cell has an open or high resistance connection, the electric

starter operation will be affected.
The power source used to provide the energy to turn an electric starter motor on Tecumseh engines is either

120 volt A.C. current or 12 volt D.C. A 120 volt A.C. starter circuit utilizes a 120 volt power source instead of a

battery. The 12 volt battery models require a charging system to maintain proper battery charge.
The starting circuit includes the battery, battery cables, starter or ignition switch, safety switches, starter solenoid,

and an electric starter motor.
The charging system consists of alternator charge coils, rectifiers or diodes, regulator, ignition switch, flywheel

magnets, and a battery. All engines that have a charging system will use a combination of some or all of these

features.

After all of the safety interlock switches have been

activated, the starter switch closes the starting circuit.

A strong magnetic force is produced by the electrical

current running through the armature windings. The

armature magnetism repels the magnetism produced

by the permanent field magnets of the electric starter.

The repelling magnetic forces cause the armature to

rotate, moving the drive pinion laterally on the splined

armature shaft, meshing the starter pinion gear with

the flywheel ring gear. When the drive pinion contacts

the stop at the end of the armature shaft, the pinion

rotates along with the armature shaft to crank the

engine. The armature and pinion remain positively

engaged until the engine fires and the flywheel rotates

faster than the armature. The greater momentum of

the flywheel throws the starter pinion gear out of mesh

and forces the starter pinion back to the disengaged

position. After the switch is released, the starting

circuit is opened and the armature coasts to a stop.

A small anti-drift spring holds the pinion in the

disengaged position (diag. 1).

CHARGING CIRCUIT

The charging system works independently of any

manual controls. The engine needs to be running to

produce an electric current flow. When a conductor

(alternating coils) cuts the magnetic field generated

by the magnets in the flywheel, a current is induced

in the alternator coil. The permanent magnets in the

flywheel have a magnetic field in which the lines of

magnetic force run from the North Pole to the South

Pole. As the flywheel rotates and the position of the

magnets change, the direction of the magnetic field

changes or alternates. The alternating coils are wound

in different directions to allow current to flow as an

A.C. waveform (diag. 2).

ROTATION OF FLYWHEEL

DUST COVER

RETAINER

SPRING
RETAINER

SPRING

END CAP

THRUST

WASHER

ARMATURE

LOCK NUT

BOLT

NUTS

WASHER

BRUSHES

www.mymowerparts.com

For Discount Tecumseh Engine Parts Call 606-678-9623 or 606-561-4983

Содержание 695244a































































































Результаты поиска

Содержание 695244a

Отзывы:

Похожие инструкции для 695244a

Бренды по названию

Популярные бренды

Tecumseh 695244a, Руководство техника

Результаты поиска

Содержание 695244a

Отзывы:

Похожие инструкции для 695244a

Бренды по названию

Популярные бренды