Tecumseh 695244a страница 12 Скачать руководство пользователя

Страница: 12 / 94

For the fuel to flow, the carburetor bowl must be either

vented externally or internally. Some internally

vented float style carburetors use a tygon tube and

a vent within the air intake. This tube must be present

for the carburetor to operate properly (diag. 3).
Air is bled into the main nozzle through the air bleed

located in the air horn. This mixes fuel and air prior

to the fuel leaving the main nozzle. Atomization occurs

as the fuel mixture contacts the fast moving air stream

and the mist flows into the intake of the engine.

FUEL PRIMERS

Primers may be mounted remotely or as an integral

part of the carburetor. The basic function of the primer

is to supply an air pressure charge to the carburetor

main well or carburetor bowl to displace fuel directly

into the carburetor venturi. This displaced fuel

provides a rich mixture necessary for engines to start

easily on the first or second attempt (diag. 4 & 5).
Primers must be vented either internally through a

passage in the carburetor air horn prior to the venturi

or externally through a hole in the primer bulb. The

vent allows atmospheric air to enter the fuel bowl

during operation and to fill the primer bulb after the

primer bulb is released.

IMPULSE FUEL PUMPS

Impulse fuel pumps may either be mounted externally

onto the carburetor fuel inlet or remotely mounted.

This pump is connected in the fuel line between the

fuel supply and the carburetor or directly to the fuel

inlet.
Impulse fuel pumps are operated by crankcase

impulses created by the up and down movement of

the piston. A hose called a pulse line connects the

fuel pump diaphragm chamber to the crankcase and

transmits the impulses to the pump diaphragm. The

impulses actuate the diaphragm and flap valves to lift

the fuel from the fuel tank to the carburetor (diag. 6).

A crankcase overfilled with engine oil can affect pump

operation.

FLOAT STYLE CARBURETORS

A float is used to maintain the operating level of fuel

in the carburetor bowl. As the fuel is used by the

engine, the fuel level in the carburetor bowl drops and

the float moves downward. This allows the inlet needle

valve to move off the sealing seat. Fuel flows by gravity

or a pulse pump into the fuel bowl. As the fuel level in

the bowl again rises, it raises the float. This upward

float motion moves the inlet needle valve to the closed

position. When the needle contacts the seat, the fuel

flow is stopped. The tapered end of the inlet needle

varies the fuel flow rate and the fuel level in the

carburetor bowl remains constant (diag. 7). The float

height is set according to the service procedure.

THROTTLE
SHUTTER

IDLE AIR
BLEED

MAIN AIR
BLEED

CHOKE
SHUTTER

INLET NEEDLE
AND SEAT

FLOAT

MAIN
ADJUSTMENT

IDLE
ADJUSTMENT

MAIN NOZZLE

PRIMER BULB

VENT

VALVE OPEN

VALVE CLOSED

FUEL SUPPLY

PULSE LINE
TO CRANKCASE

VALVE CLOSED

VALVE OPEN

CARBURETOR
FITTING

DIAPHRAGM

FILTER

AIR BLEED

ATMOSPHERIC
VENT

CRANKCASE PRESSURE
ATMOSPHERIC PRESSURE ACTING
ON DAMPING DIAPHRAGM
FUEL FLOW

CRANKCASE SUCTION AND
FLOW DIRECTION
ATMOSPHERIC PRESSURE
ACTING ON DAMPING
DIAPHRAGM

SUCTION FUEL FLOW DIRECTION
ATMOSPHERIC PRESSURE
CAUSED FUEL FLOW

TYGON TUBE

EXTERNAL VENT

PRIMER BULB

MAIN JET

MAIN NOZZLE

INTERNAL VENT

www.mymowerparts.com

For Discount Tecumseh Engine Parts Call 606-678-9623 or 606-561-4983

Содержание 695244a































































































Результаты поиска

Содержание 695244a

Отзывы:

Похожие инструкции для 695244a

Бренды по названию

Популярные бренды

Tecumseh 695244a, Руководство техника

Результаты поиска

Содержание 695244a

Отзывы:

Похожие инструкции для 695244a

Бренды по названию

Популярные бренды