TECNA 8201N Скачать руководство пользователя страница 25

Страница: 25 / 32

tecn@

WELDERS ITEM 8201N ÷ 8214N

EDITION: MAY 2008 PAGE 25 OF 32

FAULT

CAUSE

REMEDY

Too slow or not uniform
descent.

Inadequate welding pressure. It is shown by the proper

pressure

gauge.

Adjust

correctly by means of the
pressure gauge.

Faulty RFL2 flow-regulator
adjustment.

Adjust it correctly.

Low electrodes welding force. Low welding pressure.

It  is  shown  by  the  proper
pressure  gauge.  Adjust  it  by
means  of  the  welding  pressure
regulator.

The back pressure is not
removed

before

welding

(optional pneumatic circuit).

Check

that

EV2

operates

correctly and that the control unit
corresponding led

lights.

The upper electrode does not
rise up.

Low back pressure.

Correctly adjust the working
pressure.

Too closed flow regulator
RFL1.

Correctly adjust it.

Faulty solenoid valve EV2
(optional pneumatic circuit).

Replace it.

Spots

electrodes

overheating.

Insufficient cooling.

Check that water circulates in the
required quantity and at a low
temperature.

Too high welding current or
welding time.

Reduce them.

Too high post-heating time
and/or current.

Change them.

Electrodes reduced life.

Insufficient cooling.

Check that water circulates in the
required quantity and at a low
temperature.

Under-seized

electrode

comparison with the work to
carry out

Check both seize and contact
diameter.

Secondary

connections

reduced life.

Insufficient cooling.

Check that water circulates in the
required quantity and at a low
temperature.

Heating

caused

inadequate clamping of the
flexible connection.

Carefully tighten the clamping
screws.

Too high heating caused by a
too high welding rate

Reduce it.

Содержание 8201N

































Результаты поиска

Содержание 8201N

Отзывы:

Бренды по названию

Популярные бренды

TECNA 8201N, Инструкция по эксплуатации

Результаты поиска

Содержание 8201N

Отзывы:

Бренды по названию

Популярные бренды