TechVision AB-D1EWN Скачать руководство пользователя страница 21

Страница: 21 / 24

Page#

07 - Lan

08.1

Connecting to the Network

Location On Board

Connecting to the network is very easy and only requires one Ethernet Cable.

You will simply connect the Ethernet cable to the Lan Card located on the

board. then you connect the other end of the Ethernet cable to a HUB on your

network the your Computer with the Access Control Software is located. For

an even more secure connection you can plug directly into the computer. This

will ensure no one can intercept connectivity through the network.

LED

ACT

LED

LINK

LAN

IP Address

192.168.0.0

Subnet

255.255.255.0

Gateway

0.0.0.0

All of this information can be changed on the Access Control Software you

install on the PC. You will be able to connect to the board regardless of your

network configuration. The software has a finder tool built in so you can

access a new board easily.

Содержание AB-D1EWN

























Результаты поиска

Содержание AB-D1EWN

Отзывы:

Похожие инструкции для AB-D1EWN

Бренды по названию

Популярные бренды

TechVision AB-D1EWN, Быстрый старт

Результаты поиска

Содержание AB-D1EWN

Отзывы:

Похожие инструкции для AB-D1EWN

Бренды по названию

Популярные бренды