manualshive.com logo in svg

Technogym Unica Evolution, Руководство по техническому обслуживанию

Поделиться
Скачать
Technogym Unica Evolution Скачать руководство пользователя страница 55

UNICA EVOLUTION: Service & Maintenance Manual - rev. 1.1  

 

10.8.  RESET PROCEDURE 

This procedure resets the machine configuration parameters to their default values. The default 
parameter values are loaded from the program memory and overwrite those stored in the ram with 
backup battery. 
 
To do this, proceed as follows: 
 
1.  Turn off the machine. 
2.  Switch on the machine, while holding down the key furthest to the right, until the machine 

sounds 3 consecutive beeps. 

3.  The machine performs the reset sequence and loads the default parameters, as for a Chest Press. 
 
After completing this procedure, carry out the procedures described in paragraphs 10.1. “User: 
machine configuration”, 10.2. “User: ROM configuration”, 10.3. “Service: machine configuration” 
e 10.4. “Service: weight stack configuration”. 
 

  ATTENTION: the reset procedure should be used when the data in the memory with 

backup battery has been corrupted, and it is not possible to configure the parameters by 
the standard procedures. 

Page 10.23 

Содержание Unica Evolution





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды