IST-2138.KM02.01/B
Istruzione / User’s Manual / Manuel d’utilisation
Pag.4/11
TECNOCONTROL S.r.l. Via Miglioli 47 SEGRATE ( MI )
Tel: 02/26 92 28 90 Fax: 02/21 33 734
AVVERTENZA:
Non è possibile eseguire l’operazione se sono già accesi il
2° e/o il 3° LED rosso
. In questo caso
procedere alla “
Calibrazione
” con gas campione o sostituire la “
Cartuccia Sensore
”. Nel caso sia già acceso solo il
1°
Led Rosso
, invece di lampeggiare si spegnerà per conferma.
“CALIBRAZIONE”(
Codice
: F2, F2, F2, F1, F2, F1)
:
serve per ritarare il sensore con la miscela di gas sopra indicata.
AVVISO
:
per garantire che non avvengano errori d’elaborazione, esiste la rara possibilità che il LED giallo si spen-
ge ogni 8 secondi, in questo caso interrompere la procedura, spegnere e riaccendere l’apparecchio. Ripetere la Ca-
librazione, se la condizione persiste, inviare il rilevatore al fornitore per la riparazione.
Attenzione
:
Durante la Calibrazione, l’uscita in mA diventerà 0 mA.
La “
Calibrazione
” va eseguita solo in aria pulita (
ambiente senza la presenza di gas infiammabili o altri inquinanti
). Con i tasti
eseguire il “
Codice Calibrazione
”. Attendere che il LED giallo e il verde si accendano fissi e il 1° LED rosso inizi a lam-
peggiare. Infilare il TC011 sul portasensore e regolare l’afflusso del gas in modo che il flussometro indichi circa 0,3
l/min (
vedi fig. 3
) Attendere (
circa 3 minuti
), fino a quando il 3° LED rosso
si accende fisso (e mentre è
ACCESO
),
premere il tasto
F2
e tenerlo premuto finché 1° e 3° LED rosso non rimangono spenti per almeno 2 secondi (se in-
vece il 1° LED rosso, continua a lampeggiare oltre 4-5 minuti, significa che il flusso di gas non è costante o insuffi-
ciente o la concentrazione non è quella richiesta. Interrompere l’operazione, spegnere lo strumento e ripetere la Ca-
librazione).
Chiudere la bombola e togliere il TC011
. A questo punto si possono verificare due casi:
LED giallo e verde accesi:
la calibrazione è corretta, dopo 8 secondi il rilevatore si riavvia automaticamente in
funzionamento normale
(
vedi capitolo
FUNZIONAMENTO
“
Preriscaldo
”
).
LED giallo acceso:
la calibrazione è fallita
, dopo 8 secondi il rilevatore si riavvia automaticamente e dopo il preri-
scaldo, ripetere la procedura di “
Calibrazione
” senza reinserire il “
Codice
”. Se la condizione persiste anche dopo la
sostituzione della “
Cartuccia Sensore
”, inviare il rilevatore al fornitore per la riparazione.
“VERIFICA”(
Codice
: F2, F1, F2, F1)
:
serve per controllare, utilizzando la miscela di gas sopra indicata, la corretta
risposta al gas e può essere effettuata dopo la “
Calibrazione
” o dopo l’installazione, ma va eseguita soprattutto du-
rante le manutenzioni periodiche, in quanto è l’unico metodo per controllare l’effettivo funzionamento del rilevatore.
Con i tasti eseguire il “
Codice Verifica
”. Aspettare che il LED giallo lampeggi (il LED verde rimane acceso), poi infilare
il TC011 sul portasensore, regolare il riduttore della Bombola in modo che il flussometro indichi circa 0,3 l/min (
vedi
Fig.3
). Attendere circa 3 minuti e controllare che il rilevatore vada in allarme come decritto nel capitolo
“
Funzionamen-
to
”
. Se il risultato fosse diverso, effettuare la “
Calibrazione
”. Terminata la “
Verifica
”, chiudere la bombola, togliere il
TC011 e
premere il tasto F2 per ripristinare le condizioni di funzionamento normale.
NOTA
: In aggiunta a quanto sopra, se si usa anche l’uscita in mA, controllare anche, con i puntali del volmetro sui
Test-Point “
TESTmA
”, (
vedi Fig.2
) si raggiunga un valore tra
184 e 216 mV.
[
ovvero che l’uscita in mA aumenti fino a circa 20
mA (±1,6) e la centrale, cui è collegato il Trasmettitore, indichi circa 20%LIE (± 2)
].
Poi l’uscita, tornerà progressivamente a 4 mA.
EN
DESCRIPTION
The
SE138K
series is a gas detector able to detect combustible gases by employing a catalytic sensor calibrated up
to 20% LEL to different gases and find their best application in centralized alarm systems for car parks, boiler rooms,
and environments to be protected from possible leakage of gas. The instruments is flameproof certified and com-
prise of an enclosure in which the electronic circuit and the terminals are mounted and a downward facing cylindri-
cal sensor housing with inside a replaceable “
Cartridge Sensor
”. The detector has three alarm levels, with different
set-up as listed in
Table 2
. The relays are type
SSR
(
S
olid
S
tate
R
elay
) with tension free single pole contacts
(SPST)
. On
the front panel 5 Led shows the working conditions.
3rd red LED "ALARM 3":
3rd relay activation
2nd red LED "ALARM 2":
2nd relay activation
1st red LED "ALARM 1":
1st relay activation
Green LED "ON":
normal working condition
Yellow LED "FAULT":
the sensor should be faulty, disconnected, out of scale or expired.
The instrument has a 4÷20mA linear output (
S
) with
20%LIE
F.S. of detected gas. This output is connectable to a
remote Central Unit. On the
Printed Circuit Board
, F1 and F2 key using for
Test and Calibration
routine, protected by a code.
NOTES ON THE AVAILABLE MODELS
The above Gas value is on compliance with EN61779-1.
SE138KM
is calibrated to detect
Methane (CH
4
)
, a gas lighter than air. Its density as to air is 0.55 and its LEL
(
Lower Explosive Limit
) is 4.4%volume.
SE138KG (GPL)
is calibrated to detect
LPG
, a gas heavier than air and consists of a mixture of 20÷30% Propane
(C
3
H
8
) and 80÷70% Butane (C
4
H
10
). Propane density as to air is 1.56 while Butane' is 2.05. The LEL is 1.7% vol-
ume for Propane and 1.4% volume for Butane. Standard calibration to LPG is carried out for Butane gas.
SE138KI
is calibrated to detect
Hydrogen (H
2
)
, is a colourless, odourless, highly flammable gas and is the lightest
gas. Its density as to air is 0.07 and its LEL (
Lower Explosive Limit
) is 4% volume.
SE138KB (Unleaded Gasoline/Petrol)
is calibrated to detect Gasoline vapours heavier than air and highly flam-
mable. Its density as to air about 2.8 and its LEL (
Lower Explosive Limit
) is about 1.2% volume.
OPERATIONAL DESCRIPTION.
The catalytic sensor is practically insensitive to humidity and temperature variations. The calibration is carried out
for the specific gas to be detected. Anyway, it can contemporaneously detect any other flammable gas that should
be present in the same environment.
Note
that the LEDs are not visible when the enclosure is closed.