manualshive.com logo in svg

Technicolor TB30, Руководство администратора


Поделиться
Скачать
background image

 

 
TB30s SIP Administrator Guide v1.3  

 

Page 209 of 259 

Ringer in the headset. 

The ringer shall always be audible in the headset whatever the ringer level 

selected on the loudspeaker. 
 

The volume of the ringer in the headset follows the headset volume setting. 

 

Feature activation 

This is always active; it‟s a new behavior rather than a feature. Just pressing 
the volume keys when headset is active will adjust the volume for the rest of 

the current call and for the nexts, also the ringer volume, until next change. 

 
 
 

Ringer Off 

 

Now it‟s possible to turn off the ringer on the loudspeaker. 

There are 9 steps currently and the lowest step turns off the ringer. 
 

Feature activation 

This is always active; it‟s a new behavior rather than a feature. Just pressing 
the volume keys when TB30 is ringing will adjust the volume for the rest of 

the current ringing and for the nexts, until next change. 

 
 
 

Ignoring Firmware update 

 

In the INF file, if the name of the Firmware starts with the letter X (lower or 

upper case) or is empty, the IP Phone is ignoring this parameter and keep 
using its old Firmware. Moreover, the IP Phone doesn‟t display an error 
message because of this. 
 

However, if the Telconf or config files are not compatible with this old 
firmware, an error message will be displayed. 

 

Содержание TB30











































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB30

Handspring Treo 270 Specification Sheet preview
Treo 270
Бренд: Handspring Страницы: 2
palmOne Treo 600 Getting Started Manual preview
Treo 600
Бренд: palmOne Страницы: 14
Yealink Yealink SIP-T46G User Manual preview
Yealink SIP-T46G
Бренд: Yealink Страницы: 8
Blackberry 7100x Getting Started Manual preview
7100x
Бренд: Blackberry Страницы: 28
Sprint SANYO PRO-200 User Manual preview
SANYO PRO-200
Бренд: Sprint Страницы: 238
Blu DASH 4.0 User Manual preview
DASH 4.0
Бренд: Blu Страницы: 54
AU Urbano L02 Basic Manual preview
Urbano L02
Бренд: AU Страницы: 72
Talk To Me Technologies Wego Write Quick Reference preview
Wego Write
Бренд: Talk To Me Technologies Страницы: 2
Samsung SM-G9900 User Manual preview
SM-G9900
Бренд: Samsung Страницы: 158
Samsung SM-G991U1 User Manual preview
SM-G991U1
Бренд: Samsung Страницы: 179
Samsung SM-G990E User Manual preview
SM-G990E
Бренд: Samsung Страницы: 159
Samsung SM-G990W2 User Manual preview
SM-G990W2
Бренд: Samsung Страницы: 162
Samsung SM-A715FZSGTGY User Manual preview
SM-A715FZSGTGY
Бренд: Samsung Страницы: 142
Zte F116 Series User Manual preview
F116 Series
Бренд: Zte Страницы: 114
Audiovox CDM-8500 User Manual preview
CDM-8500
Бренд: Audiovox Страницы: 77
AdvanceTec AdvanceCommunicator ATT3001A User Manual preview
AdvanceCommunicator ATT3001A
Бренд: AdvanceTec Страницы: 8
Overmax vertis 4001 you User Manual preview
vertis 4001 you
Бренд: Overmax Страницы: 26
Huawei Ascend D2 User Manual preview
Ascend D2
Бренд: Huawei Страницы: 103

Бренды по названию

Популярные бренды

Загрузить еще бренды