background image

33

Troubleshooting

If your air conditioner does not work properly, first check the following points before requesting service. If it still does 
not work properly, contact your dealer or a service center.

Tips for Energy Saving

Trouble Possible 

Cause Remedy

Air conditioner does not run at all.

1. Power failure. 

1. 

After a power outage, press ON/
OFF operation button on the 
wired remote control unit.

2. Leakage circuit breaker has 

tripped.

2. Contact service center.

3. Line voltage is too low.

3. Consult your electrician or dealer.

4. Operation button is turned off.

4. Press the button again.

5. The wired remote control unit or 

heat pump is malfunctioning.
(

The inspection mark 

 and the 

letters E, F, H, L, P in 
combination with numbers 
appear on the LCD of the wired 
remote control unit.)

5. Consult your dealer.

Compressor runs but soon stops.

1. Obstruction in front of condenser 

coil.

1. Remove obstruction.

Poor cooling (or heating) 
performance.

1. Dirty or clogged air filter.

1. Clean air filter to improve the 

airflow.

2. Heat source or many people in 

room.

2.  Eliminate heat source if possible.

3. Doors and/or windows are open.

3. Shut them to keep the heat (or 

cold) out.

4. Obstacle near air intake or air 

discharge port.

4. Remove it to ensure good airflow.

5. Thermostat is set too high for 

cooling (or too low for heating).

5. Set the temperature lower (or 

higher).

6. (Defrosting system does not work.)

6. (Consult your dealer.)

Avoid

Do not block the air intake and outlet of the unit. If either is 
obstructed, the unit will not work well, and may be damaged.

Do not let direct sunlight into the room. Use sunshades, blinds or curtains. 
If the walls and ceiling of the room are warmed by the sun, it will take 
longer to cool the room.

Do

Always try to keep the air filter clean. (Refer to “Care and Cleaning”.) A 
clogged filter will impair the performance of the unit.

To prevent conditioned air from escaping, keep windows, doors and any 
other openings closed.

Should the power fail while the unit is running

If the power supply for this unit is temporarily cut off, the unit will automatically 
resume operation once power is restored using the same settings before the 
power was cut off.

NOTE

OI-722-33-EG

01_Technibel-PACi_EN.fm  Page 33  Thursday, December 9, 2004  11:36 AM

Содержание CAFP 124 RCAFP 164 RCAFP 184 RCAFP 254 RCAFP 364 R



































Отзывы: