background image

EL480zPID 

 

21 

 

 

III.m)  Set the date 

The function is used to set current date (day and month). 

 

 

 III.n) Pulser sensitivity 

With this setting you can change the sensitivity of the pulser knob within a range from 1 to 3 

(where 1 means the highest sensitivity). 

 

 

 III.o) Language selection 

Using this function, the user selects the language in which the controller will be operated. 

 

 

III.p) PID  ON/OFF 

This option enables the user to deactivate zPID control. In such a case, the controller functions 

as a two-state regulator and the menu presents the following additional functions:  

 

Fuel feeding time 

This option is used to set the feeder operation time. The value should be adjusted to the type 

of the CH boiler as well as the type of fuel used.  

 

Feeder pause 

This option is used to set the feeder pause time. The value should be adjusted to the type of 
the CH boiler as well as the type of fuel used.  

Incorrect operation and pause time may result in inefficient operation of CH boiler, i.e. unburnt 

coal left or failure to reach the pre-set temperature of the CH boiler. Appropriate pause and 
operation time ensures efficient operation of the CH boiler.  

 

Blow force 

This function is used to control the fan speed. The setting range is 1-100%. Initially the fan 

always operates at a full speed, which enables successful activation even if the motor is dusty. 

 

Temperature alarm  

This function enables the user to define when the temperature alarm is to be activated. If the 

CH boiler temperature does not reach the setpoint value during the period of time defined by 
the user, an alarm is activated and the display shows an appropriate message. The alarm may 

be deactivated by pressing OK (previous operation mode is restored).  

 

Blow force  

This function is used to control the fan speed. The setting range is 1-100% (the values may be 

regarded as fan gears). The higher the gear is, the faster the fan works. 1% is the minimum 
fan speed whereas 100% is the maximum fan speed.  

 

Operation in sustain mode 

This  option  is  used  to  set  the  feeder  operation  time  when  the CH  boiler  operates  in  sustain 
mode.  

 

Содержание EL480zPID





























Отзывы: