background image

5. DISPLAY

 

EO1-11149 

 

5.1 Upper Row (10-digit Alphanumeric Display) 

 

5- 2 

(3) Error 

Messages 

When an error occurs, an error message (programmable) is displayed in the upper row, and an error 
code is in the lower row with an error buzzer sound (a long tone).  For the error messages and error 
codes, see the table on the following page. 
Refer to the following error message table to find the cause of the error.  Press the [C] key to clear the 
error status and stop the buzzer sound, remove the cause of the error, and then operate the sequence 
again.  
 

Error 
Code 

Error message  

(Standard setting) 

Cause of the Error 

E04 

OPTION RAM 

BANK RAM Error 

E05 

PRINTER 

Printer Error 

E11 

FUNCTION 

Key Sequence or Operation Procedure Error 

E12 

CASHIER 

Cashier Error 

E13 

CTRL LOCK 

Control Lock Error 

E14 

NO CASHIER 

No Cashier error 

E16 

REPORT REQ 

Report Request Error 

E18 

HALO 

High Amount Lock Out Error  
The entered amount exceeds the pre-programmed upper limit. 

E19 

LALO 

Low Amount Lock Out Error 
The entered amount is less than the pre-programmed lower limit. 

E21 

PR PAPER 1 

Not used. 

E22 

PR PAPER 2 

Receipt Paper End Error 

E23 

PR HEAD UP 

The Paper Free Lever of the Receipt printer is raised. 

E24 

J PAPER 1 

Not used. 

E25 

J PAPER 2 

Journal Paper End Error 

E26 

J HEAD UP 

The Paper Free Lever of the Journal printer is raised. 

E32 

CODE# REQ 

Code Number Compulsory Error (Tender) 

E33 

SUB-TL REQ 

Sub-Total Key Compulsory Error (Tender) 

E34 

AMOUNT REQ 

Amount Compulsory Error 

E35 

DRW OPEN 

Drawer Open Error  
The drawer must be closed before the operation.  

--- 

SP STATUS 

Slip Printer Communication Error 

--- 

SP ERROR 

Slip Printer Hardware Error 

--- 

SP BUSY 

Slip Printer Busy  

--- 

NO RESPONS 

EFT Time Out Error 

--- 

RESPONS NG 

EFT Data Error 

--- 

EFT CANCEL 

EFT Cancel 

--- 

PIN ERROR 

EFT Pin Pad Error 

 

Содержание MA-1535-2 series























































































































































Отзывы: