TEC B-672-QQ Скачать руководство пользователя

Страница: 21 / 34

E9-1

ENGLISH VERSION EO1-33016

9. INSERTING THE OPTIONAL FLASH MEMORY CARD

9. INSERTING THE OPTIONAL FLASH MEMORY CARD

Fig. 9-1

Turn the power off.

Insert the flash memory card into the memory card slot on the rear of the printer.

Turn the power on.

NOTES: 1. Be sure to protect a flash memory card when not in use in the printer by putting it in it’s

protective cover.

2. Do not subject the card to any shocks or excessive forces.

3. Do not expose the card to extremes of heat by either storing in direct sunlight or close to

a heater.

4. Do not expose the card to excessive humidity by wiping it with a wet cloth or storing it in

a damp place.

5. Before inserting or removing the card, make sure that the power switch is turned off.

6. The following flash cards can be used. (The 1MB-card is read only and the 4MB card can

read/write.)

Flash Memory Card

WARNING!

Turn the power OFF when inserting or removing the flash memory card.

CAUTION:

To protect memory cards, discharge static electricity from your body by touching the printer rear
cover prior to touching the memory cards.

Capacity

1M Byte

4M Byte

Maker

Maxell

Mitsubishi

Maxell

Centennial Technologies INC.

INTEL

Simple TECHNOLOGY

Mitsubishi

PC Card KING MAX

PC Card

Type

EF-1M-TB AA

MF81M1-GBDAT01

EF-4M-TB CC

EF-4M-TB DC

FL04M-15-11119-03

IMC004FLSA

STI-FL/4A

MF84M1-G7DAT01

FJN-004M6C

FJP-004M6R

Device code

D0H

88H

ADH

A2H

A0H

Maker code

1CH

B0H

04H

01H

89H

Содержание B-672-QQ



































Результаты поиска

Содержание B-672-QQ

Отзывы:

Похожие инструкции для B-672-QQ

Бренды по названию

Популярные бренды

TEC B-672-QQ, Руководство пользователя

Результаты поиска

Содержание B-672-QQ

Отзывы:

Похожие инструкции для B-672-QQ

Бренды по названию

Популярные бренды