TEC B-672-QQ Скачать руководство пользователя | Manualshive

Страница: 2 / 34

background image

Copyright © 2002
by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operations of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

(for USA only)

"This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations."

"Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur de Canada."

(for CANADA only)

Changes or modifications not expressly approved by manufacturer for compliance could void the
user's authority to operate the equipment.

WARNING!

This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

CAUTION:

Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the
moving parts, push the switch in the "OFF" position to stop movement.

As an

E

NERGY

S

TAR

®

Partner, TOSHIBA TEC has determined that

this product meets the

E

NERGY

S

TAR

®

guidelines for energy efficiency.

-- Outline of the International

E

NERGY

S

TAR

®

Office Equipment Program --

The International

E

NERGY

S

TAR

®

Office Equipment Program is an international program that

promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.

E

NERGY

S

TAR is a U.S. registered mark.

«
1
2
3
4
...
»

Содержание B-672-QQ



































Отзывы:

Нет отзывов

Похожие инструкции для B-672-QQ

Бренд: NCR Страницы: 10

Бренд: Javelin Страницы: 2

Бренд: VASTEX Страницы: 15

Бренд: BIO RAD Страницы: 61

mobile pro advance

Бренд: AM TECH Страницы: 16

Бренд: Oki Страницы: 137

Бренд: Oki Страницы: 45

Бренд: Kyocera Страницы: 24

Бренд: WANHAO Страницы: 18

ScreenWriter Colour ScreenWriter

Бренд: Xante Страницы: 446

Бренд: CNET Страницы: 2

Бренд: Kyocera Страницы: 2

Бренд: aqprox! Страницы: 52

Бренд: Kyocera Страницы: 207

Бренд: Lanier Страницы: 236

Бренд: Sharp Страницы: 4

Бренд: Sharp Страницы: 5

Бренд: Sharp Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды