manualshive.com logo in svg

TEC Electronics CANTEC-F2, Руководство пользователя, Страница: 16 / 17

Поделиться
Скачать
TEC Electronics CANTEC-F2 Скачать руководство пользователя страница 16

 

 

CAN-bus 

5.

 

Reset to factory defaults

 

By hardware reset, all programmable settings and functions of the unit are restored to factory 

default and the vehicle recognition (group and sub-group) is erased. To restore factory defaults: 

•

 

Detach the unit from power source and CAN-bus. 

•

 

Press and hold the programming button. 

•

 

With the programming button pressed, supply power to the unit (CAN-bus must remain 

disconnected). The unit emits permanently short fast light signals. 

•

 

Detach the power source and release the programming button. 

 
 
 

6.

 

Specifications 

 
BATT/ACC range 

 

 

9V ~ 15V 

Stand-by power drain  

 

<4mA 

Power consumption   

 

9W 

Temperature range   

 

-40°C to +85°C 

Weight (box with harness)   

45g 

Dimensions (box only) B x H x T 

30 x 30 x 7 mm 

 
 
 
 
 

 

7.

 

Technical Support 

 
NavLinkz GmbH 

 

 

 

 

 

       TEC electronics ltd 

 

EU-distribution and tech dealer-support

 

 

 

       

manufacturer

 

 

 

Eurotec-Ring 45 

 

 

 

 

16th Parkovaya 30, Bld.1 

 

 

D-47445 Moers 

 

 

 

 

105484 Moscow, Russia 

 
Tel 

+49 2841 94997 0 

Email  [email protected] 
http://www.navlinkz.de 

 

 

 

http://www.canbus-alarm.com 

 
 
 

 

Содержание CANTEC-F2


















Отзывы:

Нет отзывов