TDT RZ6 Скачать руководство пользователя

Страница: 18 / 20

A/D

2 channels, 24-bit sigma-delta

Sample Rate

Up to 195312.50 Hz

Frequency Response

DC - 0.44*Fs (Fs = sample rate)

Voltage In

± 10.0 V

S/N (typical)

115 dB (20 Hz - 80 kHz at 5 V RMS)

THD (typical)

-90 dB (1 kHz output at 5 V RMS)

Sample Delay

66 samples

Input Impedance

10 kOhms

A and B Microphone Ampli

Single setting for both channels

High Pass Corner Frequency

3.6 Hz (Active only if the Ampli

er is enabled)

Gain Settings

20 to 65 dB

Gain Step Size

5 dB

Programmable Attenuation

2 channels

Switching Time

1 sample

Settling Time

3 usec

Transient Voltage

~370 mV

Hardware Attenuation Settings

0, 20, 40, 60 dB

Manual Attenuation

Single setting for both channels

Attenuation Settings

0 to 27 dB

Attenuation Step Size

3 dB

Output Ampli

2 channels

Spectral Variation

< 0.1 dB from 50 Hz to 200 kHz

Signal Noise

115 dB (20 Hz to 80 kHz)

THD

< 0.02% at 1 Watt from 50 Hz to 100 kHz

Noise Floor

20 uV rms

Power Output

0.75 W/channel into 5.5 ohms

Headphone Output

2 channels

Output Impedance

1 Ohm

Power Output

0.75 W/channel into 5.5 ohms

RZ6 Multi I/O Processor | 18

Содержание RZ6





















Результаты поиска

Содержание RZ6

Отзывы:

Похожие инструкции для RZ6

Бренды по названию

Популярные бренды

TDT RZ6, Справочник по аппаратуре

Результаты поиска

Содержание RZ6

Отзывы:

Похожие инструкции для RZ6

Бренды по названию

Популярные бренды