background image

 

Engine selection  - Please READ! 
The original DV8R is still flying with a JetCat P80, which is a perfect match for this model. TBM built 
its prototype ARF with a Jet Central 36 lb Rhino only to test out the DV8R’s maximum capabilities. 
The Rhino is not recommended as it is too large. We recommend the Jet Cat 70, 80, or 120 or the Jet 
Central Rabbit, Falcon or Super Eagle. The plane will weigh about 22 lbs, so a turbine with about 22 
lbs of thrust is recommended.  
NOTE that the power from the larger turbines make the plane fly very fast. The drooping nose at high 
speeds causes the plane to descend slightly. This is easily correct by changing the thrust line of the 
turbine a small amount to compensate. The plane is then rock solid at all speeds. We tested the 
prototype with a 36 lb thrust Rhino, and it was very, very fast, yet rock solid after the turbine thrust 
line was fine tuned. 

 Parts Lists (Included) 

 

1)  fuselage nose section 
2)  fuselage rear section 
3)  2 rudders/vertical fins 
4)  2 elevators/stabilizers 
5)  Canopy 
6)  Pull-pull hardware for the nosewheel steering. 
7)  Rudder linkage 
8)  Elevator linkage 
9)  Aileron linkage 
10) Flap linkage 
11)  10 small wood screws for mounting the elevator servo hatches 
12)  8 swivel clevis and horns 8-32 for all control surfaces 
13)  2- 2” titanium turnbuckles for ailerons 
14)  2- 1.5” titanium turnbuckles for flaps 
15)  2- 1.5” titanium turnbuckles for rudders 
16)  Pin hinges 

 

 

Suggested Parts List (Not Included) 

 

Содержание DV8R




































Отзывы: