background image

 

 

38 

 

Network Camera User Manual

 

www.tbkvision.com

 

 

 

Appendix 

 
 

Appendix 1 Q& A 

 
Q: How to find my password if I forget it?   

A

Reset the device to the default factory settings. 

Default IP: 192.168.226.201; User name: admin; Password: 123456 
 

Q

Fail to connect devices through IE browser, why? 

A: Network is not well connected. Check the connection and make sure it is connected well. 
B: IP is not available. Reset the valid IP. 
C: Web port number has been revised: contact administrator to get the correct port number. 
D: Exclude the above reasons. Recover default setting by IP-Tool. 
 

Q

IP tool cannot search devices, why? 

A

It may be caused by the anti-virus software in your computer. Please exit it and try to 

search device again.   
 

Q

IE cannot download ActiveX control. How can I do? 

a. IE browser blocks ActiveX. Please do setup as below. 

 Open IE browser. Click Tools-----Internet Options…. 

 

 

 

 Select Security------Custom Level…. 

 Enable all the sub options under “ActiveX controls and plug-ins”.   

 Then click OK to finish setup. 

b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them. 
 

Содержание TBK-BOX7241



















































Отзывы: