background image

2-2  

TO THE OPERATOR

085592-M 

To the Operator 

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this unit are 
warranted for the term stated in the Limited Warranty 
section in this manual. However, due to the Montreal 
Protocol and the U.S. Clean Air Act Amendments of 
1990, many new refrigerants are being tested and 
developed, thus seeking their way into the service 
industry. Some of these new refrigerants are being 
advertised as drop-in replacements for numerous 
applications. It should be noted that in the event of 
ordinary service to this unit's refrigeration system, 

only 

the refrigerant specified on the affixed data label 
should be used

. The unauthorized use of alternate 

refrigerants will void your Taylor compressor warranty. It 
is the unit owner's responsibility to make this fact known 
to any technician he employs.

It should also be noted that Taylor does not warrant the 
refrigerant used in its equipment. For example, if the 
refrigerant is lost during the course of ordinary service to 
this machine, Taylor has no obligation to either supply or 
provide its replacement either at billable or non-billable 
terms. Taylor does have the obligation to recommend a 
suitable replacement if the original refrigerant is banned, 
obsoleted, or no longer available during the five year 
warranty of the compressor.

The Taylor Company will continue to monitor the industry 
and test new alternates as they are being developed. 
Should a new alternate prove through our testing that it 
would be accepted as a drop-in replacement, the above 
disclaimer would become null and void. To find the 
current status of an alternate refrigerant as it relates to 
your compressor warranty, call the local Taylor distributor 
or the Taylor factory. Be prepared to provide the model/
serial number of the unit in question.

Содержание C152













































Отзывы: