Taylor C152 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 44

background image

Complete this page for quick reference when service is required:

Taylor Distributor: __________________________________________________________

Address:_________________________________________________________________

Phone: __________________________________________________________________

Service: _________________________________________________________________

Parts: ___________________________________________________________________

Date of Installation: ________________________________________________________

Information found on the data label:

Model Number: ___________________________________________________________

Serial Number: ____________________________________________________________

Electrical Specs:

Voltage__________________ Cycle__________

Phase__________________________________

Maximum Fuse Size: ______________________________________________________ A

Minimum Wire Ampacity: ___________________________________________________ A

Note:

Continuing research results in steady improvements; therefore, information in this manual is subject to change

without notice.

Note:

Only instructions originating from the factory or its authorized translation representative(s) are considered to be

the original set of instructions.

© 2017 Taylor Company

085592-M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be
a violation of copyright law of the United States of America and other countries, could result in the awarding of
statutory damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal
penalties. All rights reserved.

Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072

«
1
2
3
4
...
»

Содержание C152













































Отзывы:

Нет отзывов

Похожие инструкции для C152

Бренд: Ocean Страницы: 11

Бренд: C3 Custom Coolers Страницы: 2

MDF-U700VX Series

Бренд: Phcbi Страницы: 56

Бренд: Nordcap Страницы: 36

Бренд: Yeti Страницы: 12

Бренд: B SCIENCE Страницы: 48

Бренд: INVENTOR Страницы: 36

Бренд: Hamilton Beach Страницы: 28

KFN 14842 SD cs-1

Бренд: Miele Страницы: 76

Бренд: Miele Страницы: 72

KFN 29683 D obsw

Бренд: Miele Страницы: 108

Бренд: Miele Страницы: 72

Бренд: Miele Страницы: 56

KFN 14842 SD ed/cs

Бренд: Miele Страницы: 68

Бренд: Miele Страницы: 68

KFN 14943 SD ed

Бренд: Miele Страницы: 64

KFN 14943 SD ed/cs

Бренд: Miele Страницы: 64

KFN 29683 D brws

Бренд: Miele Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды