manualshive.com logo in svg

Taylor 810 Series, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Taylor 810 Series Скачать руководство пользователя страница 55

CONTROLS AND SYSTEMS

2-25 

Model 810, 812, 820, 822, 828 Series 

Controls and Systems 

2

8. Adjust the four corners of the platen by using a 

3/16 in. hex-key wrench, until the platen is just above 
the height of the GO end on the GO NO-GO gauge.

Note:  

Turning the wrench clockwise will increase the 

gap between the platen and the lower cooking 
surface. Turning the wrench counterclockwise will 
decrease the gap.

9. Select a corner adjustment block to start in. Rotate 

the GO gauge with the end positioned beneath the 
adjustment block. Lower the corner until the upper 
platen surface first makes contact with the GO 
gauge. Moving in a clockwise direction, adjust each 
of the remaining corners until the upper platen 
surface just comes in contact with the GO gauge.

Note:  

You may find that after three corners are 

adjusted to touch the GO end of the gauge, the fourth 
corner rests slightly higher. In this case, adjust the 
corner directly opposite of the higher corner in order 
to balance the difference. When the platen is level, 
the cables should not be loose. There should be 
some tension on each cable, although it may not be 
equal.

10. Tighten down all four locknuts with a 3/8 in. 

straight-blade screwdriver.

11. Insert the 3/16 in. hex-key wrench into the 

adjustment screw and try to turn it clockwise. If it can 
be turned, the locking screw is not tight against the 
adjustment screw. Take it apart and reassemble by 
threading the screw into the base by one thread and 
then into the adjustment block by one thread. Re-gap 
the grill.
Insert the 3/16 in. hex-key wrench into the 
adjustment screw again and verify that it cannot be 
turned clockwise. If it cannot be turned, proceed to 
the next step. Otherwise, repeat the corrective 
measures taken in this step until the screw cannot be 
turned.

12. Cycle the platen up and down three times and then 

check with the GO gauge to validate that the platen 
remains level. At this point, the platen should be 
level, and all fine adjustments to the gap setting will 
be made using the control.

Adjusting the Gap Offset

1. Check the gap setting with the GO NO-GO gauge 

(X79617). If the gap setting is within the correct 
tolerance, no further adjustments to the platen are 
necessary and you can proceed to step 6.

2. If the gap setting does not pass the GO NO-GO 

inspection, fine adjustments can be made in the 
controls Gap Calibration mode.

3. Adjust the gap offset by pressing the Up arrow key to 

increase the offset or the Down arrow key to 
decrease the offset. (Each increment represents 
approximately one thousandth [.001] of an inch.) 
Continue to adjust, until the new setting made with 
the control is within the tolerance range of the GO 
NO-GO gauge.

4. Exit the calibration mode by pressing the EXIT key 

until the control returns to the User Menu.

5. Press the RAISE button to raise the platen to the 

Open position.

6. After the platen gap has been set correctly, re-install 

the platen cover.

7.

Repeat this procedure

 for the remaining platens.

Содержание 810 Series

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды