Taylor-Dunn RE-380-36 Скачать руководство пользователя страница 31

Страница: 31 / 150

Front Axle

Page 31

MR-380-05

RE-380-36 & RE-380-48

INSTALL

1: Raise the front of the vehicle and support with jack stands.

2: Install the front axle in reverse order of removal.

NOTE:

Use all new cotter pins.

NOTE:

Refer to the Replacing the Ball Joints section for information regarding the installing the ball joints

or rod ends.

NOTE:

Refer to Tires and Wheels section for information regarding removing the front wheels.

3: Realign the front wheels. Refer to Steering Component Service section for information regarding realigning

the front wheels.

4: If equipped with front brakes, bleed the brakes. Refer to Brake Service section for information regarding

bleeding the brakes.

5: Lower the vehicle.

6: Reconnect the main positive and negative cables at the batteries.

7: Remove the blocks from behind the wheels.

8: Release the park brake and test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание RE-380-36























































































































































Результаты поиска

Содержание RE-380-36

Отзывы:

Taylor-Dunn RE-380-36, Инструкция по обслуживанию и замене запасных частей, Страница: 31 / 150

Результаты поиска

Содержание RE-380-36

Отзывы: