Taylor-Dunn RE-380-36 Скачать руководство пользователя страница 126

Страница: 126 / 150

Replacement Parts

Page 126

MR-380-05

RE-380-36 & RE-380-48

CHARGER, SIGNET

Note: The harness connectors and AC plug

are not included with the charger.

QTY

PART #

DESCRIPTION

75-318-20

Butt splice

75-320-51

Knife connector

76-200-00

AC plug, 115 volt

Model HBS Charger

PART #

DESCRIPTION

79-309-42

48 volt Flooded Batteries (WET, FLA)

79-309-43

48 volt Sealed Batteries (GEL, SLA, AGM)

Note: There are no user serviceable components inside the charger

Note: The charger AC cord is an integral part of the charger. When replacing the charger, do not cut

and splice the AC cord.

Cutting the AC cord will void the charger warranty.

Note: The Signet model HBS series charger replaces all previous Signet models.

Standard Single Phase AC wire Color Codes as of 2010.

Note: Older systems may use a alternate color code.

Refer high voltage wiring repairs to a qualified technician

United States / Canada

Neutral: White

Hot: Black or Red

Ground: Green

IEC (Europe) and United Kingdom

Neutral: Blue

Hot: Brown

Ground: Green/Yellow

Содержание RE-380-36























































































































































Результаты поиска

Содержание RE-380-36

Отзывы:

Taylor-Dunn RE-380-36, Инструкция по обслуживанию и замене запасных частей, Страница: 126 / 150

Результаты поиска

Содержание RE-380-36

Отзывы: