Taylor-Dunn C0-426-48AC Скачать руководство пользователя страница 41

Страница: 41 / 132

Steering

Page 41

MC-425-15

C-426

REPLACE BALL JOINT

1: Raise the front of the vehicle and support with

jack stands.

2: Loosen the ball joint clamp on the steering

sleeve.

3: Remove the cotter pin and ball joint nut.

4: Using a pickle fork, remove the ball joint from the

steering arm.

5: Remove the ball joint from the steering sleeve.

Note: Count the number of turns needed to remove

the ball joint.

6: Install the new ball joint into the steering sleeve.

Screw it into the sleeve the same number of turns

counted in the previous step. Do not tighten the

ball joint clamp at this time.

7: Install the ball joint into the steering arm. Tighten

the ball joint nut per torque listed in the Hardware

Torque table at the end of this section and install

a new cotter pin.

8: Realign the front wheels. Refer to the Front Axle

section for information regarding realignment of

the front wheels.

9: Lower the vehicle.

10: Reconnect the main positive and negative cables

at the batteries.

11: Remove the blocks from behind the wheels.

12: Release the park brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

REPLACE STEERING WHEEL

Note: The steering wheel is on a tapered shaft and

may be damaged when it is removed.

1: If equipped with a horn switch in the steering

wheel, remove the switch and disconnect the

wires from the switch.

2: Remove the steering wheel nut.

3: Using a steering wheel puller, remove the

steering wheel.

4: Position the front wheels in the straight ahead

position.

5: Lightly grease the steering wheel splines and

install the replacement steering wheel orientated

as shown in the illustration.

6: Tighten the steering wheel nut to torque listed

in the Hardware Torque table at the end of this

section.

7: Reinstall the horn switch (if equipped).

8: Reconnect the main positive and negative cables

at the batteries.

9: Remove the blocks from behind the wheels.

10: Release the parking brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание C0-426-48AC





































































































































Результаты поиска

Содержание C0-426-48AC

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn C0-426-48AC, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание C0-426-48AC

Отзывы:

Бренды по названию

Популярные бренды