Taylor-Dunn C0-426-48AC Скачать руководство пользователя страница 11

Страница: 11 / 132

Page-11

MC-425-15

Introduction

C-426

HOW TO IDENTIFY YOUR VEHICLE

This manual is valid only for the serial numbers listed on the front cover. If the ending serial number is blank, then

this manual was for current production vehicles when printed. If you did not receive this manual with the vehicle,

you should confirm this manual is valid for your serial number at the Taylor-Dunn web site.
The locations of the model and serial numbers are shown in the illustrations below:

WEB SITE REGISTRATION

Registering on the Taylor-Dunn web site will give you access to a wealth of information about your vehicle and the

entire Taylor- Dunn line of vehicles. Your contact information will remain confidential and will not be shared outside

of the Taylor-Dunn corporation.
Once registered on the Taylor-Dunn web site, you will have access to:

• Additional Taylor-Dunn product information.

• Worldwide Taylor-Dunn dealer contacts

• Vehicle Service, Maintenance, Operator, Troubleshooting, and Parts manuals.

• Replacement part number lookup utility

www.taylor-dunn.com

Data plate on the kick panel

ID tag on the frame

Содержание C0-426-48AC





































































































































Результаты поиска

Содержание C0-426-48AC

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn C0-426-48AC, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание C0-426-48AC

Отзывы:

Бренды по названию

Популярные бренды