Taylor-Dunn C0-425-36 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 246

Taylor-Dunn C0-425-36 Скачать руководство пользователя страница 156

Electrical Troubleshooting

Troubleshooting

Page 2

Test Equipment Required:

• Digital multimeter (DMM) with diode test function, FLUKE 79 model shown.
• Test harness, Taylor-Dunn #75-089-00

Important Notes and Instructions

• This troubleshooting guide assumes a familiarity with the use of a digital multimeter

including, voltage tests, continuity tests, and diode testing. If you are not familiar with
these types of tests then refer testing to a qualified technician.

• These tests are not intended to locate a problem on an incorrectly wired vehicle.
• Make sure the batteries are in good condition and fully charged before performing any

tests.

• If the vehicle exhibits intermittent problems, it must be in the failed mode for troubleshooting.

If it is running normally when the testing is done then the problem will not be identified.

• Some tests refer to a High/Low switch. The High/Low switch is optional and the vehicle

may not be equipped with this option. If the vehicle is without this option, there is a jumper
bypass installed in place of the switch in the dash.

• All voltage tests are done referenced to battery negative, unless otherwise specified.

•

At the start of each test sequence you will be instructed on how to place the control
switches. While testing, do not change the position of any switches unless instructed to
do so.

DURING ALL TESTS

• After any repairs are made, completely retest vehicle before lowering the drive wheels to

the ground.

Definitions:

• Battery volts = full voltage available at

the batteries at the time of test.

• High: Greater than +4.5 volts
• Low: Less than +1.8 volts

Terminology used:

• The “HOT” side of a switch is the terminal

that the power is connected to.

• The “COLD” side of a switch is the

terminal that the power is switched to.

• FS-1 = Micro-switch in the accelerator

module.

The rear drive wheels may rotate during some of the following tests.

Block the front wheels, raise the rear drive wheels off the ground, and

support the vehicle with jack stands. Failure to do so may cause the

vehicle to move and cause property damage and/or serious bodily injury.

Turn the Key switch OFF then disconnect both of the battery leads during

any maintenance or before disconnecting any electrical component or

wire. Failure to do so may cause severe bodily injury and/or property

damage.

Turn the Key switch OFF BEFORE disconnecting the batteries.

Disconnecting the batteries with the key switch ON may corrupt the

controller programming resulting in a fault code 1 (refer to fault table).

«
...
154
155
156
157
158
...
»

Содержание C0-425-36























































































































































































































































Отзывы:

Нет отзывов