background image

Service/Maintenance Guidelines

Page  16

Bigfoot G-1500

MB-440-10

REPLACEMENT PARTS

Using Non-OEM Replacement Components

To maintain peak performance, always use original Taylor-Dunn replacement parts intended for use on your vehicle.

Taylor-Dunn components are designed and tested for use on specific Taylor-Dunn model vehicles. Only use the 

correct Taylor-Dunn replacement components for your Taylor-Dunn vehicle.

Electrical Components

Electrical components not tested by Taylor-Dunn (or intended for use on other Taylor-Dunn vehicles) may have 

unanticipated interaction and/or interference with the vehicles control system resulting in unsafe vehicle operation 

or damage to the electrical system.

Mechanical Components

Mechanical components not tested by Taylor-Dunn (or from other model Taylor-Dunn vehicles) may have an 

undesirable affect on the operation of the vehicle, result in additional frame stress, or stress other components 

resulting in premature failure or an unsafe condition.
Due to the unknown properties of non-Taylor-Dunn tested components or from components not originally equipped 

on the vehicle, we cannot approve their use in a Taylor-Dunn vehicle.

To maintain peak performance, always use original Taylor-Dunn replacement parts intended for use on your 

vehicle. Taylor-Dunn components are designed and tested for use on specific Taylor-Dunn model vehicles. Only 

use the correct Taylor-Dunn replacement components for your Taylor-Dunn vehicle.
Do not modify your vehicle:

Modifications to this vehicle may have an undesirable effect on the operation of the vehicle, result in additional 

frame stress, or stress other components resulting in premature failure or an unsafe condition  and may lead 

to an accident resulting in serious injury or death.

WARNING

Содержание Bigfoot G-1500























































































































Отзывы: