background image

 

8

 

Ver_2-08-22

 

 

 
 

 
 

 

 

ADIR Semi

Automatic 

3” filter

 TDS 

 Gen2

 

Installation and maintenance instructions

 

2 action

 

 

Box contents 

 

Main filter assembled 

 picture A

  

 

 

Valve 2" FF 

 picture L 

 

Valve F/F 1/2" and Nipple M/M 

½” –

 picture B 

 

Pressure indicator kit and fittings 

 picture C 

o

 

Pressure indicator (Picture C-3).                    

o

 

Tube 6 mm length 25 cm (Picture C-4). 

o

 

Tube 6 mm length 20 cm (Picture C-5). 

o

 

Threaded couplers 1/4"F x 2 (Picture C-6) 

o

 

Connectors 1/4"M to 6 mm elbow x 2  
(Picture C-7). 

o

 

Connector 1/4"F to 6 mm elbow (Picture C-8). 

o

 

Connector 1/4"F to 6 mm adaptor (Picture C-9). 

Assembly  

Connect the 2” flush

 valve to the bottom of the filter cup, 

(no need to use Teflon, valve is self-seal) 

 Picture E 

Make sure handle open position is away from filter cup.

 

 

 

Connect the valve 1/2" with nipple 1/2” t

o the flush port 

outlet (no need to use Teflon, valve is self-seal) 

 

 (Picture B). 

 

Pressure indicator kit assembly: 

o

 

Connect two threaded couplers 1/4"F to filter 
body top 1/4" outlets. 

o

 

Connect two 1/4"M to 6 mm elbow to the 
threaded couplers 1/4"F.   

o

 

Connect 1/4"F to 6 mm elbow to the bottom of 
the indicator (upstream - high pressure). 

o

 

Connect 1/4"F to 6 mm adaptor to side of the 
indicator (downstream 

 low pressure). 

o

 

Press fit the indicator to the sockets on the filter 
body.  

o

 

Connect 6 mm tube length 25cm from Filter inlet 
port to indicator bottom (marked "+"). 

o

 

Connect 6 mm tube length 20 cm from Filter 

outlet port to indicator side (marked "-"). 

o

 

Hydraulic fittings may require Teflon to seal. 

 

Filter is ready for installation (Picture D) 

 

Installation 

 

Filter can be installed in vertical position or at 90° to the 

pipe, (Bottom of the cup

 

pointing down or to the side). 

 

Ensure proper flow direction as clearly marked on the 
filter. 

 

Make sure valve 1/2" is closed. 

 

It is recommended to install a shut off inlet valve before 
the filter for maintenance. 

 

Filter is ready for first operation 

 

 

 

 

           

            
  
         

 

 
   

950mm 

795mm 

235mm 

595mm 

 

 

 

   
 

 
 

 
           

 

          

 

      
 

 

 
 

 
 

 
 

 
 

 
 

      

 
        

 

Picture A 

Before 

assembly 

Picture B 

Picture C 

Picture D After 

assembly 

Picture L 

Содержание TDS

















Отзывы: