Taurus GEYSER ECO 2800, Инструкция по эксплуатации

Страница: 12 / 70

ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Select the minimum position (MIN) using the
thermostat control.
- Unplug the appliance from the mains.
- Remove the water from the water tank.
- Clean the appliance.
CLEANING
- Unplug the appliance from the mains and let it
cool down before performing any cleaning task.
- Clean the appliance using a damp cloth with a
few drops of detergent and then dry it.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
- Do not immerse the appliance in water or any
other liquid, or place it under a running tap.
SELF-CLEANING FUNCTION:
- It is important to self-clean the appliance at least
once a month to remove calcium and any other
built-up minerals inside the iron.
- Fill the water tank to its maximum level, as indi -
cated in the “filling with water” section.
- Place the iron in an upright position, plug in to
the mains and select maximum temperature.
- Leave the appliance to heat up until the pilot
light indicates that it has reached its consigned
temperature.
- Unplug the appliance and place it in the sink.
- Press and hold the self-clean button.
- Let the water flow out through the steam vents
in the base, while lightly shaking the appliance.
- Release the button after a minute or when the
tank becomes empty.
- Leave the iron in the upright position until it has
cooled.
ANTISCALE FILTER REPLACEMENT (FIG. X)
GEYSER ECO 3000
(ATTENTION) Make sure there is no water in the
tank.
1 Rest the iron on its heel, rotate the wheel
counter-clockwise until it reaches its limit and
the arrow is aligned with the open padlock sign
(approx. 180º) and pull it backward.
2 To reinsert the filter, align the arrow with the
open padlock sign and turn clockwise, as shown
in the drawing, at the same time pressing the
piece inwards until it is aligned with the closed
padlock sign.
When the filter is in position, make sure it DOES
NOT PROTRUDE from the rear end of the
appliance. Otherwise, this means it has not been
correctly inserted and water will come out of the
tank.
* HOW TO DEAL WITH LIME SCALE INCRUS-
TATIONS:
- For the appliance to work correctly it should be
kept free of lime scale or magnesium incrusta-
tions caused by the use of hard water.
- To prevent this kind of problem, we recommend
the use of water with low lime or magnesium
mineralisation.
- However, if it is not possible to use the kind of
water recommended above, you should periodi -
cally replace the iron’s anti-scale cartridge:
• Every 12 weeks if the water is “very hard”.
• Every 18 weeks if the water is “hard”.
- To do so, we recommend the use of a specific
product for this type of appliance, on sale in
specialised shops and authorised technical
services.
- A specific anti-scale cartridge should be used for
this type of appliance.
- Homemade solutions are not recommended for
de-scaling this appliance, such as the use of
vinegar.
FAULTS AND REPAIR
- Take the appliance to an authorised technical
support service if problems arise. Do not try to
dismantle or repair it, as this may be dangerous.
- If the mains cable has been damaged, it must
be replaced, proceed as in the case of a fault.
FOR EU PRODUCT VERSIONS AND/OR IN
THE CASE THAT IT IS REQUESTED IN YOUR
COUNTRY:
ECOLOGY AND RECYCLABILITY OF THE
PRODUCT
- The packaging materials for this appliance
are included in a collection, classification and
recycling system. Should you wish to dispose of
them, use the appropriate public containers for
each type of material.
- The product does not contain concentrations of
substances that could be considered harmful to