tau K101M, Перевод оригинальной инструкции

Страница: 9 / 12

9
11. DIAGNOSIS LED
DL1 LED
Other than indicating the programming of a transmitter is going on, DL1 LED advises error messages as follows:
Steady light:
Normal operation;
Slow flashing: Automatic 50 / 60 HZ Frequency Detection Error;
Contact Technical Service;
8 flashes: No motor signal;
Check wiring - Make sure the motor can rotate freely;
Multiple errors are indicated by a 2” pause between error messages. Messages will be shown until a complete opening/closing cycle is performed.
12. ADVANCED FUNCTIONS
Clock function: a timer can be connected to the open-close pushbutton in order to keep the automation open at certain times during the day,
after which it reverts to automatic closing.
Note: The automation remains open as long as the OP/CL input continues to be activated.
13. 433.92 MHz BUILT-IN RADIO RECEIVER
The radio receiver can learn up to a maximum of 30 codes of rolling code (S2RP, S4RP, K-SLIM-RP, T-4RP) to be set freely on 3 channels.
The first channel directly commands the control board for opening the automatic device; the second channel commands a relay for a N.O. no-
voltage output contact (terminals 19 - 20, max. 24V AC, 1 A) and the third channel controls directly the pedestrian opening from the controller.
LEARNING SYSTEM FOR RADIO CONTROL DEVICES
CH1 = 1
st
channel (OPEN/CLOSE) CH2 = 2
nd
channel CH3 = 3
rd
channel (PEDESTRIAN)
1_ Press button CH1 briefly to associate a radio control device with the OPEN/CLOSE function;
2_ the (green) DL8 LED is ON to indicate the code learni ng mode has been activated (if no code is entered within 10 seconds the board exits
the programming function);
3_ press the button of the relative radio control device;
4_ the (green) DL8 LED turns off to indicate saving is complete and then on again immediately waiting for other radio control devices (if this
is not the case, try to re-transmit or wait 10 seconds and restart from point 1);
5_ to memorise codes to other radio control devices, press the key to be stored on other devices within 2-3 sec. After this time (DL8 LED turns
off) must repeat the procedure from point 1 (up to a maximum of 30 transmitters);
6_ if you wish to save on the 2nd channel, repeat the procedure from point 1 using the CH2 key instead of CH1 (in this case the DL8 LED is yellow);
7_ to program transmitters into the third channel, repeat procedure from point 1 using CH1 and CH2 buttons at the same time (DL8 will turn on red);
8_ to exit the learning mode without memorising a code, press button CH1 or CH2 briefly.
If the maximum number of radio controls is reached (30), the LED DL8 will begin to flash rapidly for about 3 seconds but with -
out performing memorisation.
REMOTE PROGRAMMING BY MEANS OF T-4RP / K-SLIM-RP / S-2RP / S-4RP (V 4.X)
With the new version of software V 4.X it is possible to carry out the remote self-learning of the new version of transmitters T-4RP / K-SLIM-RP
/ S-2RP / S-4RP (V 4.X), that is without pressing the receiver’s programming buttons.
It will be sufficient to have an already programmed transmitter in the receiver in order to start the procedure of remote programming of the
new transmitters. Follow the procedure written on the instructions of the transmitter T-4RP / K-SLIM-RP / S-2RP / S-4RP (V 4.X).
CANCELLING CODES FROM RADIO CONTROL DEVICES
1_ Keep button CH1 pressed for 3 seconds in order to cancel all the associated radio control devices;
2_ LED DL8 flashes slowly to indicate that the cancellation mode has been activated;
3_ press button CH1 again for 3 seconds;
4_ LED DL8 turns off for approx. 3 seconds and then remains steady to indicate that the code has been cancelled;
5_ repeat the procedure from point 1 using button CH2 to cancel all the associated radio control devices;
6_ repeat procedure from point 1 using CH1 and CH2 buttons at the same time to erase all transmitters programmed into the third channel;
7_ to exit the learning mode without memorising a code, press button CH1 or CH2 briefly.
MEMORY CAPACITY
The code memory capacity* of the control unit can be expanded from 30 to 126, 254 or 1022 codes (transmitters) by replacing the memory cards as
follows (plug them onto J3 connector, see wiring diagram):
126 codes Art. 250SM126
254 codes Art. 250SM254
1022 codes Art. 250SM1022
* Control units are supplied with a standard built-in 30-code memory. The memory card for enhancing the code memory capacity must be ordered
separately.
To allow the previously stored codes (max. 30) to be moved to the control unit, it is required to install a memory card, making sure that the
control unit is at that time off and that the memory card is brand new and therefore completely empty.
When the control unit is restarted, the codes will automatically move to the memory card.
Moving the codes from the control unit to the memory card does not work if on the memory card used, radio control codes have already been
stored and the memory card has been subsequently erased.
To insert new radio controls, the operation described above shall be repeated.
WARNING: Control unit must be turned OFF to insert / remove a memory card.
RADIO MEMORY RESET:
- press without releasing keys CH1 and PROG till LEDs DL7 and DL8 start flashing quickly with a yellow light. At this point release the keys and
press them again till the LEDs go off confirming the operation is complete (if they are not pressed the board reverts to normal operation
after about 12 seconds).