TATU 05.03.03.3933 Скачать руководство пользователя

Страница: 73 / 84

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

GAPCR-HD 8013/GASPCR-HD 9017/GASPCR-EHD 10020

Wheelset hubs lubrication

Maintenance

•

For models with 9.00 x 20 tires - 14 ply and 600/50 x 22.5 tires - 16 ply.

Check the retainer position (A) to let the excess of grease flow out of the hub and be

careful to not damage the retainer.

Adjust the flat washer (B) and the castle nut (C) on the hub using a wrench to get

some resistance while turning the hub. Do not totally tighten it. Lock it using a cotter pin (D).

Place 5 small flanges (E) on the wheelset hub (F) using a bolt (G) and nut (H). Place

a dust cap (I) facing the wheelset hub (F), the hub cap (J) and lock using a bolt (K) and

spring washer.

Whenever the retainer is damaged, replace it immediately.
Do not forget to apply the specific grease, that is a lithium soap grease for this

equipment, grade NLGI 2 with Extreme Pressure additive, anticorrosive and antioxidant.

Содержание 05.03.03.3933





















































































Результаты поиска

Содержание 05.03.03.3933

Отзывы:

Похожие инструкции для 05.03.03.3933

Бренды по названию

Популярные бренды

TATU 05.03.03.3933, Руководство оператора

Результаты поиска

Содержание 05.03.03.3933

Отзывы:

Похожие инструкции для 05.03.03.3933

Бренды по названию

Популярные бренды