Taski Swingo 450B Скачать руководство пользователя страница 44

Страница: 44 / 63

Technical Manual

31. May 2007

Revision: V1.10

6-3

08.0 swingo 450B - trouble shooting.fm - 31. May 2007

Part

Position

Order

No.

Do/ Perform

Then

Else

Batteries

•

Make sure the batteries are

connected and charged

correctly

•

Measure Voltage of

batteries

V = > 24 V DC

(if possible power

check under load)

Check battery fuse Charge batteries/

perform power

test on batteries/

exchange batter-

ies

Fuse 75A

08/132

4122607

•

Measure if the battery

voltage is present after the

fuse

Voltage is same

after fuse as on

batteries

Check Connec-

tions

Connec-

tions

08/143

08/142

4091300

4091310

•

Measure if the battery

voltage is present after the

charger jack

Voltage is same

after charger jack

as on fuse

Check if power is

present on elec-

tronics 450B

Connect charger

jack/

Exchange charger

jack

Electron-

ics 450B

01/116

4126576

•

Measure power on

electronisc 450B

Voltage is same on

cooler body of

electronics as on

charger jack

Check fuse of elec-

tronics 450B

Replace wires

Fine Wire

Fuse

01/111

4122605

•

Remove the fuse from the

electronisc 450B

•

Measure resistance

R = approx. 0

Ohm

Check key

Exchange fuse

Key

08/144

4122551

•

Is the key set complete

Yes

Check plugs

Exchange key

Connec-

tors elec-

tronics

450B

01/116

4126576

•

Check if all plugs are

positioned correctly

Yes

Exchange elec-

tronics 450B

Position the con-

nectors correctly

Table 2: Troubleshooting - Does not witch on

Содержание Swingo 450B




















































Результаты поиска

Содержание Swingo 450B

Отзывы:

Taski Swingo 450B, Техническое руководство, Страница: 44 / 63

Результаты поиска

Содержание Swingo 450B

Отзывы: