Taski swingo 1255B Power Скачать руководство пользователя страница 50

Страница: 50 / 110

GTS

Technical Manual

19. April 2010

Edition: V1.00/2010

5-29

05.0 s

go 1255 B Power - me

anics

.fm

•

Push bolts inwards to release the brush unit.

Make sure that you hold the brush drive unit firmly.

•

Pivot the complete brush drive unit out.

Mount

On EBU models the brush unit fixation bolts are different in length.

Therefore the small bolt (06/115) is mounted on the LH and the

longer bolt (06/121) on the RH side.

•

Position the brush drive unit onto the cradles.

•

Position the bolts and mount the retaining ring (06/110) on

the LH and the RH side.

•

Position the axle (06/114) and mount the circlip (06/112).

•

Connect the brush motor wires to the power electronics.

•

Connect the fresh water hoses to the brush drive unit.

•

Position the brush housing on the brush drive unit.

•

Position the brush housing fixation screws and tighten them.

•

Close and lock the battery compartment on both sides with the

screws of the locking system.

Adjustment

•

M5 (04/125) with 5 Nm

•

Brush minus

•

M6 (04/128) with 7 Nm

•

Brush plus

Содержание swingo 1255B Power


































































































Результаты поиска

Содержание swingo 1255B Power

Отзывы:

Похожие инструкции для swingo 1255B Power

Бренды по названию

Популярные бренды

Taski swingo 1255B Power, Техническое руководство

Результаты поиска

Содержание swingo 1255B Power

Отзывы:

Похожие инструкции для swingo 1255B Power

Бренды по названию

Популярные бренды