Taski swingo 1255B Power Скачать руководство пользователя страница 48

Страница: 48 / 110

GTS

Technical Manual

19. April 2010

Edition: V1.00/2010

5-27

05.0 s

go 1255 B Power - me

anics

.fm

5.1.6.3 Replacing of electrical brush unit (EBU)

Picture 29: Electrical brush unit

Remove

•

Lay machine on the LH side.

•

Remove special screw (06/136) to release tie rod.

•

Disconnect the linear drive wiring.

•

Pull out stop pin (06/108).

•

Remove bolt (06/107) for the linear drive fixation.

Remarks

To pull out the bolt, you need to thread in a screw into the bolt.

Dimensions: M6, length > 30mm.

•

Thread out the complete linear drive.

Mount

•

Thread in the complete linear drive.

Adjustment

The distance between the linear drive fixation bracket and the outer

end of the tie rod has to be as bellow.

Picture 30: Linear drive fixation distance

•

Mount bolt for linear drive fixation and secure with stop pin.

•

Connect linear drive wiring.

•

Mount special screw to fix the tie rod.

•

Lift up machine again.

Содержание swingo 1255B Power


































































































Результаты поиска

Содержание swingo 1255B Power

Отзывы:

Похожие инструкции для swingo 1255B Power

Бренды по названию

Популярные бренды

Taski swingo 1255B Power, Техническое руководство

Результаты поиска

Содержание swingo 1255B Power

Отзывы:

Похожие инструкции для swingo 1255B Power

Бренды по названию

Популярные бренды