Task Force Tips ZCF1T3 Скачать руководство пользователя страница 24

Страница: 24 / 24

©Copyright Task Force Tips LLC 2014-2018

LIZ-060 October 26, 2020 Rev03

TASK FORCE TIPS LLC

MADE IN USA · tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

10.0 OPERATION AND INSPECTION CHECKLIST

BEFORE EACH USE, appliances must be inspected to this checklist:

1. There is no obvious damage such as missing, broken or loose parts, dents, cracks, corrosion, or other defects that could impair

operation

2. The waterway is clear of obstructions

3. Monitor is securely attached to the mount

4. Hose and nozzle are securely attached

5. All swiveling elements rotate freely

6. Monitor is pointed in a safe direction

BEFORE BEING PLACED BACK IN SERVICE, appliances must be inspected to this list:

1. There is no obvious damage such as missing, broken or loose parts, dents, cracks, corrosion, or other defects that could impair

operation

2. The waterway is clear of obstructions

3. Valves opens and closes smoothly and fully

4. There is no damage to any thread or other type connection

5. All locks and hold-down devices work properly

6. Internal gaskets are in good condition

7. All swiveling connections rotate freely

8. There are no missing parts or components

9. The marking for maximum operating pressure is visible

10. There are no missing, broken, or worn lugs on couplings

WARNING

Equipment failing any part of the checklist is unsafe for use and must have the problem corrected

before use or being placed back into service. Operating equipment that has failed the checklist is a

misuse of this equipment.

Содержание ZCF1T3

























Результаты поиска

Содержание ZCF1T3

Отзывы:

Похожие инструкции для ZCF1T3

Бренды по названию

Популярные бренды

Task Force Tips ZCF1T3, Инструкция по установке

Результаты поиска

Содержание ZCF1T3

Отзывы:

Похожие инструкции для ZCF1T3

Бренды по названию

Популярные бренды