background image

©Copyright Task Force Tips LLC  2002-2020 

LIX-512 August 17, 2020 Rev09

10.0 MAINTENANCE

The Extend-A-Gun requires little maintenance. The Extend-A-Gun should be kept clean and free of dirt. All controls should be 

checked for freedom of movement and proper operation before each use. Any inoperable or damaged parts should be repaired or 

replaced immediately. Consult factory for recommended service procedure.

10.1 LUBRICATION

The Extend-A-Gun is permanently lubricated on the cup seal. If lubricant has been removed during service, apply a thin film of White 

Lithium Grease on seal surfaces.

10.2 REPAIR

Factory service is available with repair time seldom exceeding one day in our facility. Factory serviced equipment is repaired by 

experienced technicians, wet tested to original specifications, and promptly returned. Repair charges for non-warranty items are 

minimal. Any returns should include a note as to the nature of the problem and whom to reach in case of questions.
Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability 

for damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at tft.com for 

parts lists, exploded views, test procedures and troubleshooting guides.
Performance tests shall be conducted on the equipment after a repair, or anytime a problem is reported to verify operation in 

accordance with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the 

equipment. Any equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides 

are available with each test procedure or equipment can be returned to the factory for service and testing.

CAUTION

Any alterations to the product or its markings could diminish safety and constitutes a misuse of 

this product.

NOTICE

All replacement parts must be obtained from the manufacturer to assure proper operation of the 

device.

11.0 EXPLODED VIEW AND PARTS LIST

Exploded views and part lists are available at tft.com/serial-number.

Содержание Extend-A-Gun XG12

















Отзывы:

Похожие инструкции для Extend-A-Gun XG12