Task Force Tips Extend-A-Gun XG12 Скачать руководство пользователя страница 3

Страница: 3 / 16

©Copyright Task Force Tips LLC 2002-2020

LIX-512 August 17, 2020 Rev09

1.0 MEANING OF SAFETY SIGNAL WORDS

2.0 SAFETY

3.0 GENERAL INFORMATION

3.1 SPECIFICATIONS

3.2 USE WITH SALT WATER

3.3 VARIOUS MODELS AND TERMS

3.4 XG12 SERIES DIMENSIONS

4.0 BRACKET SETS

4.1 SELECTION OF STRUCTURAL SUPPORT ON FIRE TRUCKS

4.2 BRACKET INSTALLATION

4.2.1 TUBE BRACKET INSTALLATION (EXTEND-A-GUN RC3 ONLY)

4.2.1.1 TUBE BRACKET WELDING

4.2.2 SADDLE BRACKET INSTALLATION

4.2.2.1 SADDLE BRACKET WELDING

4.2.3 PLATE BRACKET INSTALLATION

5.0 MANUAL EXTEND-A-GUN SIDE LOADS AT MOUNTING POINTS WORKSHEET

5.1 EXTEND-A-GUN LOAD CHARTS

5.2 INDICATOR LIGHT

5.2.1 INDICATOR SWITCH WIRING

6.0 MOUNTING MONITORS

7.0 USE OF DRAIN

8.0 OPERATING INSTRUCTIONS

8.1 EXTEND

8.2 RETRACT

9.0 WARRANTY

10.0 MAINTENANCE

10.1 LUBRICATION

10.2 REPAIR

11.0 EXPLODED VIEW AND PARTS LIST

12.0 OPERATION AND INSPECTION CHECKLIST

Table Of Contents

Содержание Extend-A-Gun XG12

















Результаты поиска

Содержание Extend-A-Gun XG12

Отзывы:

Похожие инструкции для Extend-A-Gun XG12

Бренды по названию

Популярные бренды

Task Force Tips Extend-A-Gun XG12, Инструкции по установке, безопасной эксплуатации и обслуживанию

Результаты поиска

Содержание Extend-A-Gun XG12

Отзывы:

Похожие инструкции для Extend-A-Gun XG12

Бренды по названию

Популярные бренды