TASCAM CD-6010
35
7 – Other Functions
Checking the firmware version
To check the firmware version, use the
21 INFO
menu
item.
1 Select the
21 INFO
menu item.
2 Press the TRACK SKIP/DATA knob on the main unit or
the ENTER button on the remote control to show the
system firmware version on the display.
Version
Build number
3 Press the TRACK SKIP/DATA knob on the main unit
or the ENTER button on the remote control again to
return to menu item selection.
Digital output format setting
You can set the format of the digital signal output from
the
COAXIAL
and
XLR DIGITAL OUTPUTS
. You can set
the output format using the
22 D-OUT
menu item. The
digital signal output format options are as follows (default
value:
AES
).
SPD
S/PDIF (consumer)
AES
AES/EBU with U bit (professional)
AE_
AES/EBU without U bit (professional)
NOTE
The digital output format setting is retained even when the
power is turned off.
Analog output attenuation
You can set the unit so that the analog output level
is attenuated by -4 dB. Set this appropriately for the
equipment connected to the outputs.
Use the
19 ATT
menu item to set whether or not -4dB
attenuation is used or not (default value:
OFF
).
NOTE
The attenuation setting is retained even when the power is
turned off.
Using the parallel connector
Using the
CONTROL I/O PARALLEL
connector, you can
use external parallel control to operate this unit.
Pin
No.
Function
(Pin 14 = H or Open)
Function
(Pin 14 = L)
IN/
OUT
1
GND
GND
-
2
PLAY
FLASH 1
In
3
STOP
FLASH 2
In
4
INDEX/DIR SEARCH FWD
FLASH 3
In
5
TRACK SKIP FWD [
¯
]
FLASH 4
In
6
TRACK SKIP REV [
Â
]
FLASH 5
In
7
INDEX/DIR SEARCH REV
STOP/LOAD
In
8
FADER START/STOP
(Reserved)
In
9
FLASH LOAD TALLY
FLASH LOAD TALLY
Out
10
PAUSE TALLY
PAUSE TALLY
Out
11
NO DISC TALLY
(Reserved)
Out
12
STOP TALLY
STOP TALLY
Out
13
PLAY TALLY
PLAY TALLY
Out
14
REMOTE SELECT*
REMOTE SELECT*
In
15
PAUSE
FLASH 6
In
16
CALL
FLASH 7
In
17
SEARCH FWD [
]
FLASH 8
In
18
SEARCH REV [
Ô
]
FLASH 9
In
19
(Reserved)
FLASH 10
In
20
(Reserved)
FLASH PAGE**
In
21
EOM TRACK TALLY
EOM TRACK TALLY
Out
22
(Reserved)
(Reserved, fixed high)
Out
23
RELAY OUT
(EOM DISC TALLY)
(Reserved)
Out
24
(Reserved)
(Reserved, fixed low)
Out
25
+5V*
+5V*
-
IN: external command reception (operates active low,
when ground 30 ms or longer)
OUT: transport status display signal by open drain
(20V maximum voltage, 35mA maximum current, 10Ω
impedance)
*When pin 14 (REMOTE SELECT) is high or open, the
functions in the left column are active and ordinary
parallel control can be used. When set to low, the
functions in the right column are active and they can be
used as flash start keys.
**When pin 14 (REMOTE SELECT) is low, the high/low
status of pin 20 (FLASH PAGE) determines the track
assignments as shown below.
***100mA maximum supplied current
#14
#20
Flash start tracks
Low
High
1–10
Low
Low
11–20
The following connection example shows playback
control by fader start/stop.
START
STOP
Pin 1
FADER START
Pin 8
GND
PARALLEL
