background image

38

WARRANTY

WARRANTY DISCLAIMER:

This limited warranty is in lieu of, and Tarter Farm and Ranch Equipment disclaims and excludes any express and 
implied warranties with respect to the product including, without limitation, merchantability, and fitness for a particular 
purpose. No other express warranty, whether written or oral, given by any person or entity, including a retailer, with 
respect to any product, shall bind Tarter Farm and Ranch Equipment.

Tarter Farm and Ranch Equipment’s exclusive liability for breach of the limited warranty, as set forth above, on the 
product shall be to repair or replace the implement within the warranty period in accordance with the terms of this 
limited warranty. The choice of remedy shall belong solely to Tarter Farm and Ranch Equipment. In no event shall 
Tarter Farm and Ranch Equipment be liable for any loss or damages of any other kind, whether direct, incidental, 
consequential including lost profits, exemplary, special, or otherwise, including without limitation, expenses incurred 
for substitute or replacement implement or for rental expenses to temporarily replace a warranted product.
 
Under no circumstance shall recovery, of any kind, be greater than the amount of the purchase price of the product 
purchased. Customer assumes all risk and liability for loss, damage, or injury to customer or customer’s property and/
or the property of others arising out of the misuse or inability to use the product.

LEGAL RIGHTS

This limited warranty gives you specific legal rights, and you may also have other rights which may vary from state to 
state. Some states do not allow any limitation on how long an implied warranty lasts or the exclusion or limitation of 
incidental or consequential damages, so the above limitations may not apply to you.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 

KEEP FOR YOUR RECORDS

Record the model number, serial number, and the date of purchase with the original sales receipt. This information will 
be helpful to the retailer if parts or service are required.

Model Number 

_______________________________

Serial Number 

_______________________________

Date of Purchase 

_____________________________

Retailer 

____________________________________

Содержание RC104BL









































Отзывы: