Tarter RC104BL Скачать руководство пользователя страница 17

17

12. Do not pull back on pin this will release latch.
13. Lower tractor PTO shield, if equipped.  

CHECKING DRIVELINE/CUTTER 

CLEARANCE

1.  Raise cutter slowly and check for clearance between 

driveline shield and cutter deck.

2.  Check clearance between tractor tires and foot guards 

or chain deflector.

3.  Check to see if hitch height position will provide 

clearance desired.

4.  Shorten center link or lengthen lift links to provide 

clearance. (See your tractor Operator’s manual.)

5. Raise and lower cutter slowly to check for binding 

or interference. Check cutter-to-tractor driveline 
telescoping length to ensure that it does not bottom 
out. Modify driveline if necessary. (See MODIFYING 
PTO DRIVELINE in Assembly section.)

ATTACHING TO A TRACTOR

 
 

1. Back up tractor to cutter with hitch points

approximately in alignment.

2. Engage tractor parking brake and/or place

transmission in Park.

3. Shut off tractor engine and remove key.
4.  Remove center link mounting hardware and hitch pin 

assemblies at both hitch masts.

   5.  Install tractor draft links on hitch pins. Secure with 

quick lock pins (stored on tractor draft links.)

6.  Align center link with upper hole in cutter mast straps 

and install center link mounting hardware.

7. Shut off tractor engine.
8. Raise tractor PTO shield, if equipped.

9. Support driveline, cradling it in your hand.
10.  Pull pin back toward cutter. Align splines by rotating 

cutter driveline. Push driveline onto tractor PTO shaft 
until pin snaps into place.

11.  Pull back on shield to make sure driveline is locked.

ATTACHING

DANGER: To avoid bodily injury or machine 
damage whenever Rotary Cutter is attached, 
put transmission in PARK position and check 
the full range of hitch for interference, binding, 
or PTO separation. Do not stand between 
tractor and Rotary Cutter.

IMPORTANT: Prevent driveline damage from 
contact with frame or machine damage from 
contact with tractor tires. Raise cutter slowly 
and check for interference. If necessary, 
shorten center link or lengthen lift links to 
provide clearance to full lift height.

NOTE: Final adjustments should be made 
before operating cutter. See ADJUSTING 
CUTTING HEIGHT AND ANGLE in Operating 
the Cutter section. Center link should be 
installed in lowest hole at tractor end if there 
are multiple holes. Lift height may also be 
limited by installing stops on rockshaft control 
lever bracket.

NOTE: If the tractor draft links will not open 
wide enough to fit over hitch pin assemblies in 
their normal configuration the hitch pins can 
be inverted so that the draft links can hook up 
to the inside.

DANGER:  Shut off tractor engine before 
attaching PTO driveline. Entanglement in 
rotating driveline can cause serious injury or 
death.

IMPORTANT:  Keep driveline and powershaft 
splines clean of paint, dirt and chaff. Apply 
grease to tractor PTO shaft before attaching 
PTO driveline.

IMPORTANT:  PTO driveline may be too long 
for some tractor models, causing tractor 
transaxle damage. Hold driveline sections 
parallel to each other and check for a 
minimum of 6 inches overlap.

IMPORTANT:  Do not use shielding bell on 
driveline to lift driveline into position. Damage 
to shielding can occur.

Содержание RC104BL









































Отзывы: