TapFlo SK Series Скачать руководство пользователя страница 4

 

 

EU DECLARATION OF CONFORMITY 01/EU/SUB/2022 

 
 
Series: 

SG

SPT…; S

K

…; SF…; SFA…; SB…; SBA…

 

 
Manufactured for: 

Tapflo AB 
Filaregatan 4 
44

2 34 Kungälv, Swe

den 

 
This declaration of conformity is issued under the sole responsibility of the manufacturer. 
 
Object of declaration: 

SUBMERSIBLE SINGLE-STAGE CENTRIFUGAL PUMPS

 

 

The  object  of  the  declaration  described  above  is  in  conformity  with  the  relevant  Union 
harmonisation legislation: 

 

Directive 2006/42/EC of European Parliament and of the Council of 17 May 2006 on machinery, 
amending Directive 95/16/EC; 

 

Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the 
harmonisation  of  the  laws  of  the  Member  States  relating  to  electromagnetic  compatibility 
(recast); 

 

Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the 
harmonisation of the laws of the Member States relating to the making available on the market 
of electrical equipment designed for use within certain voltage limits; 

 

Mr Michał Śmigiel is authorized to compile the technical file.

 

 

Tapflo Sp. z o.o. 

 

ul. Czatkowska 4b 

 

83-110 Tczew 

 

 

Signed for and on behalf of Tapflo AB 

 
 
 

Håkan Ekstrand

 
 

Managing director 

Kungälv

, 14.02.2022 

Содержание SK Series




































Отзывы: