Important
- Please leave the humidifier in the room for at least half an hour before use, especially
when the outdoor temperature is below 5
℃/41°F
;
- Do not turn on the unit when no water is in the tank, it will cause serious damage;
- Do not touch the water in the sink or any component of the sink while the unit is working.
Add Water
- Remove the water tank from the base;
- Twist to loosen the switch of the filter on the bottom of the water tank and fill water in
the tank; then twist the filter back on;
- Put the tank back on the base;
Note:
Do not fill the water tank via the nozzle.
How to Use
- Turn the switch clockwise pass the “ON” position. A tick sound indicates the humidifier
has been turned on. The LED indicator will be green to show it has started working;
- Keep turning the switch clockwise to increase evaporation level. Maximum
evaporation is 300mL/h;
- Turn the switch counterclockwise to the “OFF” position to turn off the humidifier. The LED
indicator will be off to show it has stopped working.
Low Water Protection
When the water level drops below a minimum amount, the LED indicator will become
red. When water is depleted, the humidifier will automatically power off.
Clean the Water Tank
1. Make sure the unit is turned off;
2. Remove the water tank from the base;
3. Rinse the tank with clean water and wipe off any water on the outside of the tank
before putting it back.
Cleaning the Base / Transducer / Filter
- Please be careful when cleaning the unit. Any water splashing inside the base may
damage the unit;
- Make sure the unit is turned off;
- Empty the water from the base;
- Use a towel to wipe clean the base. Do not use organic solvent like alcohol or
acetone to clean the base;
- To clean the transducer, pour some white vinegar on the transducer;
- Fill a small amount of warm water and wait for 3 to 5 minutes;
- Clean the transducer by using the included brush;
- Rinse clean the transducer;
- To clean the filter, simply dip the filter in white vinegar for 10 minutes and rinse clean
with water.
Caution
- Please do not dismantle the product by yourself, always ask professional electrician or
authorized technician for repairing;
- If you smell bad odor or anything unusual, please turn off the unit immediately;
- Please do not remove the power plug with wet hands as it may cause electrical shock;
- It is not a toy. Keep away from children;
- Do not place this unit on sloping or uneven surface to avoid water leaking or
component damage;
- Do not put this unit near any heat source or under direct sunlight;
- Keep away from other electric appliances that are prone to humidity damage;
- Using the unit in a space larger than 150m
3
will reduce its effectiveness;
- Regularly clean the unit if it won’t be used for a long period; store in a
dry and shady place.
Trouble Shooting Guide
Problem
LED indicator is off, the
unit does not work
LED indicator is red, but
no mist or wind
LED indicator and the
wind are on but no mist
LED indicator is on and
the water tank has water,
but it shows there is no
water
Bad / Strange smell
The mist output is too
small
Possible Cause
No power supply
Unit not powered on
No water in water tank
Too much water in the
water sink
Mist output is set to the
lowest level
Floater is jammed
New unit
Dirty water or the water
has extended its storage
period
Stain built up on the
transducer
Dirty water or the water
has extended its storage
period.
The water is too cold
Solution
Connect power supply
Power on the unit by
turning the switch
Fill water into water tank
Pour out some water from
the water sink and close
the cover of water tank
tightly.
Adjust the mist output
Stir the floater to keep it
flowing smoothly
Take out water tank, open
cover. Put it in the room
without any operation for
at least half an hour
Clean water tank, refill
with clean water
Clean the transducer
Clean water tank,
change to fresh and
clean water
Add some warm water
inside
05/06
