TAO F125 Скачать руководство пользователя страница 57

Страница: 57 / 76

The engine oil level should be checked before each ride. In addition, always follow the maintenance schedule for oil changes as shown in

the maintenance schedule.

1. Place the ATV on a level surface.

2. Check the engine oil level on a cold engine.

3. Remove the engine oil filler cap, and then wipe the engine oil dipstick off with a clean rag.

4. Slowly thread the dipstick back in the filler hole, and then remove it again to check the oil level.

5. If the engine oil is at or below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level.

NOTICE: Be sure the engine oil is at the correct level, otherwise engine damage may result.

6. Check the 0-ring for damage, and replace it if necessary.

7. Insert the dipstick into the oil filler hole, and then tighten the engine oil filler cap.

1. Minimum Oil Level Mark

2. Maximum Oil Level Mark

TIP

To check the engine oil level

NOTE

Your new vehicles engine comes with shipping oil, shipping oil must be changed before the engine is

started for the first time. Please see specification chart for recommended oil type.

If the engine was started before checking the oil level, be sure to warm up the engine sufficiently, and

then wait at least ten minutes until the oil settles for an accurate reading.

The engine oil dip stick is located on the right side of the ATV behind the right foot rest .

TIP

Only add engine oil into the dipstick filler

hole

. Never

pour

engine oil anywhere else

other than dipstick filler hole.

ENGINE OIL

Содержание F125













































































Результаты поиска

Содержание F125

Отзывы:

TAO F125, Руководство пользователя, Страница: 57 / 76

Результаты поиска

Содержание F125

Отзывы: