background image

- 8 - 

 

Limited Warranty, Terms and Conditions 

Tanks, Inc. provides a limited warranty for MeterMatch.  If a unit should fail within 180 days from time 
of shipment from Tanks, Inc., it can be returned for repair or replacement at Tanks, Inc. discretion.  
Products subject to abuse (as determined by Tanks, Inc.) are excluded from this limited warranty.   
Tanks, Inc. makes no other claims as to suitability and excludes any liability for direct, indirect or 
consequential damages.  Exclusive remedy is limited to product replacement or repair.  Cost of 
shipping the returned product to Tanks, Inc. is at the customer’s expense, but the 
replacement/repaired MeterMatch will be shipped to the customer via USPS or UPS ground at Tanks, 
Inc. expense, except for shipments out of the US, in which case Tanks, Inc. shipping cost is limited to 
the cost of domestic shipments.  When returning MeterMatch to Tanks, Inc., include a description of 
the fault to help facilitate repair.  Risk of damage/loss during shipping becomes the customer 
responsibility once the product is delivered to a common carrier by Tanks, Inc. 

 

 

MeterMatch

TM

 Specifications 

 

Size 

1.85"x2.4"x0.93" 

Weight 

1.2 Oz 

Connections 

1x5 screw terminal strip accepting #14-#22 AWG wires, slots in case sized for #18 

AWG (.093”). 

Input voltage 

7 Vdc – 16 Vdc 

Sender Input 

Ohmmeter reading of sender input to ground 

Max current through sender 50mA 

Max voltage at sender input: 5Vdc 
Resolution approximately 1 

  for readings less than 1 k 

Range 0-3,000 

  

Gauge output 

Constant-current sink 

Full output range resolution better than 1%, actual resolution depends upon 

working range of gauge 

Input/Output Translation 

Meter output current based on linear interpolation of sender resistance calibration 

points.    

Four calibration points provided, minimum of two necessary for operation. 

Alarm LED Output 

Programmed blinking 

Open collector output with approximately 400

 Ω 

 series resistance between output 

and ground 

Controls 

Up, Down, Save buttons 

8-Position rotary switch 

 

 

 

 

MeterMatch MM-02 Instruction Manual Rev F (Rev 7/2020) 

Содержание MeterMatch









Отзывы: