TANKLESS 000 Btu/hr Скачать руководство пользователя

Страница: 15 / 72

CARING FOR YOUR WATER HEATER

Water Heater Inspections

Venting System

(Direct Vent Only)

The venting system should be inspected annually by

a qualified service technician to ensure all of the vent

sections are secure and airtight.

WARNING:

DO NOT

operate the water

heater if the vent system shows signs of leaking exhaust.

Leaking exhaust could lead to death, personal injury, and/

or product failure.

Check the air intake and vent outlet for blockage and/

or debris.

Condensate Trap

(Direct Vent Only)

CAUTION:

DO NOT

operate without the

condensate trap connected to the vent and routed to the

proper drain. It could cause the system to malfunction or

fail.

On a regular basis, inspect the condensate trap to

ensure there is enough water in the trap and the

condensate is draining properly.
Ensure that condensate is disposed of per local codes

and regulations.

Use Instructions

Outdoor models

Содержание 000 Btu/hr









































































Результаты поиска

Содержание 000 Btu/hr

Отзывы:

Похожие инструкции для 000 Btu/hr

Бренды по названию

Популярные бренды

TANKLESS 000 Btu/hr, Инструкция по использованию и уходу

Результаты поиска

Содержание 000 Btu/hr

Отзывы:

Похожие инструкции для 000 Btu/hr

Бренды по названию

Популярные бренды