TANKLESS 000 Btu/hr Скачать руководство пользователя

Страница: 13 / 72

Use Instructions

USING YOUR WATER HEATER

WARNING:

Flammable vapors can be

drawn by air currents from surrounding areas to the

water heater. Vapors can ignite causing death, personal

injury, or product damage.
• DO NOT store or use flammable or combustible

materials (gasoline, paint thinner, adhesives,

newspapers, rags, mops, etc.) in the vicinity of the

water heater or any other gas appliance. If they must

be used, open doors and windows for ventilation, and

shut off all gas-burning appliances, including their pilot

lights.

• DO turn off manual gas shut-off valve if water heater

has been subjected to overheating, fire, flood, physical

damage, or if the gas supply fails to shut off.

• DO NOT turn on water heater unless water and gas

supplies are completely opened.

• If there is any difficulty in understanding or following

the operating and care instructions in this manual, it

is recommended that you contact a qualified service

technician to perform the work.

Safety Precautions

Setting the Water Temperature

D A N G E R

HOT

Water temperature over 125

can cause severe burns

instantly or death from scalds.

Children, disabled and elderly are

at highest risk of being scalded.

See instruction manual before

setting temperature at water

heater.
Feel water before bathing or

showering.
Temperature limiting valves are

available, see manual.

BURN

Time/Temperature Relationship in Scalds

120°F (49°C)

More than 5 minutes

125°F (52°C)

1 1/2 to 2 minutes

130°F (54°C)

About 30 seconds

135°F (57°C)

About 10 seconds

140°F (60°C)

Less than 5 seconds

145°F (63°C)

Less than 3 seconds

150°F (66°C)

About 1 1/2 seconds

155°F (68°C)

About 1 second

Table courtesy of Shriners Burn Institute

DANGER:

Water temperatures above 125°F (52°C) will result

in death and/or severe burns from scalding.
Safety and energy conservation are factors to be considered when

selecting the water temperature setting. The temperature of the water in

the water heater can be regulated by setting the temperature on the front of

the remote control. Be sure to read and follow the warnings outlined on the

pictured label.
The remote control has been preset and shipped at the recommended

temperature setting.
Safety factors should be considered whenever altering the water

temperature setting. The chart below may be used as a guide in

determining the proper water temperature for your home.

Water

Time to Produce

Temperature

a Serious Burn

Содержание 000 Btu/hr









































































Результаты поиска

Содержание 000 Btu/hr

Отзывы:

Похожие инструкции для 000 Btu/hr

Бренды по названию

Популярные бренды

TANKLESS 000 Btu/hr, Инструкция по использованию и уходу

Результаты поиска

Содержание 000 Btu/hr

Отзывы:

Похожие инструкции для 000 Btu/hr

Бренды по названию

Популярные бренды