TANDBERG VCS Скачать руководство пользователя страница 8

Initial configuration

5

Follow the prompts given by the install wizard to specify the following:

9. 

the password you want to use for your admin account 

• 

i

For security reasons you should change the password from the default of 

TANDBERG.

 

whether you wish to use IPv4, IPv6 or Both

• 

the LAN 1 IP address of the VCS

• 

the LAN 1 IPv4 subnet mask of the VCS (if you have selected IPv4)

• 

the IP default gateway of the VCS

• 

the Ethernet

• 

 speed 

i

 Use the default value of 

Auto

 unless the switch to which you are connecting 

is unable to auto-negotiate. 

whether you want to use SSH to administer the VCS

• 

whether you want to use Telnet to administer the VCS.

• 

After the wizard is finished the following message will appear, and you will be prompted 
to log in again:

Setting other settings... 
OK. The system must be restarted for new 
settings to take effect.. 

Login with the username 

10. 

admin

 and your new password.

You will again get the install wizard prompt; this time select 

11. 

n

 and press 

Enter

 in order to 

skip the wizard. 
A welcome message similar to the following will appear: 

Welcome to 
TANDBERG VCS Release X4.1 
SW Release Date: 2009-01-31 
OK

You must now reboot the system in order for the new settings take effect.  To do this, 

12. 

type the command: 

xCommand boot

Disconnect the serial cable and store it in a safe place.

13. 

After it has rebooted, the VCS is ready to use. For security reasons you should now change 
the password for the default admin account (if you have not already done so) and the root 
account from the default of TANDBERG.  See the sections “Changing the admin account 
password” and “Changing the root account password” on page 6 for details. 

i

The IP configuration made using the install wizard applies to the LAN 1 Ethernet port 

only.  If you have enabled the LAN 2 port (by installing the Dual Network Interfaces 
option key) you must use the web interface or CLI to configure the LAN 2 settings.

Содержание VCS











Отзывы: