TANDBERG VCS Скачать руководство пользователя страница 6

Initial configuration

3

Press the soft power button on the back left of the unit. The system will power up.  Wait 

2. 

until:

the green PWR LED on the front of the unit is a steady green color (it may flash briefly 

• 

during power up)
the red ALM LED on the front of the unit has gone out

• 

the IP address is showing in the display panel on the front of the unit.

• 

i

If the red ALM LED flashes rapidly it indicates a hardware fault. Contact your local 
TANDBERG representative. The yellow HDD LED indicates disk activity and may 
flicker during normal operation, more so on a busy system.

Initial configuration

Before you can use the VCS, you must configure its IPv4 address, subnet mask and default 
gateway.  Consult your network administrator for information on which addresses to use. Note 
that the VCS must use a static IP address.
This initial configuration can be done:

by connecting from a PC to the VCS using

• 

 a serial cable.  This is the recommended 

process, and is described in the following section
by using

• 

 the buttons on the front panel.  See the VCS Administrator Guide for details

if your network is set up to allow it, by 

• 

connecting using a web browser to the default 

IP address of 192.168.0.100 (described in “Using the web interface” on page 7).

Initial configuration using a serial cable

To set the initial configuration using a PC connected to the VCS 

DATA

 port via a serial cable:

Connect the Ethernet LAN cable from the 

1. 

LAN1

 port on the front of the VCS to your 

network. 
Connect the supplied serial cable from the 

2. 

DATA

 port on the front of the VCS to the serial 

port on a PC.

DATA

 port

LAN1

 port

Figure 2: VCS front view

Содержание VCS











Отзывы: