TANDBERG MXP 770 Скачать руководство пользователя страница 79

Страница: 79 / 79

Glossary

PAL: Phase Alternation by Line. Video standard corresponding to 4CIF. Primary used in Europe,

Middle East and Asia.

PIP: Picture-In-Picture

Point to point call: A call with two participants including yourself.

POP: Picture Outside Picture. POP is a picture layout mode that is optimized for wide screens:

Full screen, 1+3 layout and side by side layout.

Presentation: Presentation means to show another video source. Use the Presentation Key for a

predefined presentation source. Use the presentation menu to choose among all
available video sources.

Remote: Short for remote control.

Restart: Restarts the system.

Restore defaults: Restores system settings to the factory defaults.

Selfview: Outgoing video. In most cases, the image of yourself.

System status: Lists IP-address, MAC-address, software version, serial number and other useful

information about the system.

Touch tones: To dial extension numbers ect. during a call, use touch tones in order to get tones

instead of preset on the number keys.

Welcome menu: The welcome menu displays the main menu when you are outside a call.

Содержание MXP 770
















































































Результаты поиска

Содержание MXP 770

Отзывы:

Похожие инструкции для MXP 770

Бренды по названию

Популярные бренды

TANDBERG MXP 770, Руководство пользователя

Результаты поиска

Содержание MXP 770

Отзывы:

Похожие инструкции для MXP 770

Бренды по названию

Популярные бренды