Tamerica VERSALAM-2700HC Скачать руководство пользователя страница 13

- 12 - 

 

within  the 10-day grace period.    Further, you will have to cover freight to return the machine and it 

has to be in brand-new resalable condition, otherwise, you might incur more charges. 

 

This  warranty  covers  all  defects  incurred  in  the  normal  use  of  the  equipment  except  in  the 

following cases: 

 

1.

 

  Loss or damage to the equipment due to improper operation, abuse, mishandling or failure to 

follow the operating instructions. 

2.

 

  Removal or alteration of the serial number. 

3.

 

  The  machine  being  serviced  or  modified  by  anyone  other  than  a  certified  technician 

authorized by TAMERICA. 

 

This  warranty  expresses  the  entire  obligation  of  the  Manufacturer.  Unless  prohibited  by  law,  neither 

this  warranty  nor  any  other  warranty  expressed  or  implied,  including  implied  warranties  of 

merchantability, shall extend this warranty period. Again, no responsibility is assured for incidental or 

consequential damages. 

 

This warranty is valid only within the United States, or its provinces and territories. 

 

 

Содержание VERSALAM-2700HC














Отзывы: